Always losing remotes?

Have you had someone ringing you,

 to enter your property whilst you are away?

 

Now arsparks has the answer!

 

*GSM*

 

 

 

Open your electric gates from anywhere in the world from your mobile. Control who enters your property remotely via a mobile or landline. Let visitors or workmen gain access whilst you're away. Fits to any make of electric gate.

  

SO you are fed up with broken gate or garage door remotes

 

 then make them a thing of the past and open your gates

 

with your mobile or home phone

 

GSM opening devices can be added to most automation

 

systems quickly and easily

 

Contact Adrian for more details

info@arsparks.co.uk 

 

  gsm intercom

 

Frequently asked questions about GSM control

Do I need a telephone line?

No the GSM-AUTO uses the GSM mobile phone network in the same way as a mobile phone

Will it work anywhere?

It will work anywhere in the world where there is a GSM network and the GSM-AUTO can receive a signal

Can it be activated from another country?

It can be activated from anywhere in the world as long as you have access to a telephone

Can anyone activate the GSM-AUTO by calling it?

Yes and no, the GSM-AUTO can work in open access mode whereby it will respond to any call made to it, or secure access mode when it will only respond to authorised numbers

Do I have to use a special SIM card?

No, you can use any networks SIM card

What are the call costs?

The GSM-AUTO uses the mobile phone network and the same as a mobile phone it has a SIM card, when you call the GSM-AUTO it rejects the call without answering and switches on the device connected to it so there are no call costs incurred. When the GSM-AUTO is initially programmed it sends a confirmation sms text message and this will be charged at your network operators rate. A T-Mobile pre-pay (pay as you go) SIM card is supplied so there are no monthly network charges

Do I have to use a mobile phone to activate the GSM-AUTO?

No it can be activated using a landline

What is the cost of the GSM unit and the instillation cost?

The GSM unit costs in the regen of £230 to £??? depending on GSM unit and the

application Fitting would be from £60 to £??? depending on application  

 

 

 

 

 gsm intercom with key pad     gsm intercom installers

 gsm intercom fitters

 

 

 

 

Please contact Adrian  for more details

 

info@arsparks.co.uk 

 

 

Adrian _____07971 475 781    email  adrian@arsparks.co.uk

 

 Gates, RailingsGate Automation, Electric Gate ServicingAccess Control , CCTVcctv, CCTV  Servicing, CCTV Hire, GSM Control, Heating ControlHome AutomationHome EntertainmentTV Aerials, Fire Alarms, Security AlarmsPhone Points, Network Points, Outside Power/Lighting, Fish Pond Power & Lighting, Industrial & Commercial  Electrics Electric Gates, Electric Gate kits, Automatic gatesAutomatic gate kits, gate openers, electric gate openers, electric sliding gates, automatic sliding gates, electric gate spares, electric gate motors, sliding electric gates, security gatesremote controlled gates, gate motors, driveway gates, timber gates, hardwood gates, wrought iron gates, diy electric gate kits, diy gate openers, automatic bollards, automatic rising bollards, security bollardsManual bollardsrising barriers, barriers, automatic barriers,manual barriers, automatic doors, swing gates, electric swing gates, Anti crush gate automation, anti crush,Low energy lighting, LED lighting, low cost lightingtape led lighting, fidh pond power/ lighting  

HERE ARE JUST SOME OF THE AREAS WE COVER

 Coventry, Birmingham, Clent, Romsley, Belbroughton, Hagley, Netherton, Quinton,Merry Hill, Pedmore,  Wordsley, Hagley, Cookley, Stourton, Prestwood, Envil, Fairfiled, Barnt Green, Licky End, Evesham, Pershore, Malvern, Chaddasley corbett, Bromsgrove, Droitwitch, Stourbridge, Ludlow, Tenbury Wells, Ashward Bank, Aston, Acocks Green, Amblecoat, Briely Hill, Dudly, Harvington Cradley, Edgbaston, Erdington, Earlswood, Great bar, Sandwell, West Bromwich Harborne, Halesowen, Marston Green, Hampton in Arden, Hay Mills, Hockly, Kings Norton, Kingswinford, Edgebaston, Knowle, Lye, Mosley, Old Hill, Perry Bar, Rowley Regis, Quinton, Sandwell, Sheldon, Small Heath, Smethwcik , Solihull, Tipton, Walsall, Wensburry, Willenhall, Yardley, Wolverhampton, Walsall, Sutton Coldfield, Solihull, Nuneaton, Redditch, Warwick, Leamington Spa, Rugby, Stafford, Burton upon Trent, Tamworth, Stoke on Trent, Telford, Tamworth, Worcester, Grantham, Northampton, Kettering, Rugby, Corby, Stamford, Peterborough, Huntingdon, Cambridge, Milton Keynes, Luton, Bedford, Newmarket, Chester, Manchester, Stockport, Rochdale, Bolton, Warrington, Altrincham, Runcorn, Crewe, Chesterfield, Sheffield, Barnsley, Huddersfield, Wakefield, Halifax, Bradford, Leeds, Dewsbury, Worksop, Newark, Lincoln, Mansfield, Rotherham, Doncaster, Scunthorpe, Hull, Harrogate, York, Burnley, Blackburn, Shrewsbury, Watford, London, St Albans, Luton, Stevenage, Oxford, Cheshire, Sandbatch, Midlands, Yorkshire, Staffordshire, Nottinghamshire, Derbyshire, Leicestershire, West Midlands, East midlands, Nottingham, Derby, Leicester,

MAYBE WE SHOULD JUST PUT THE UK 

GSW2 UNIVERSAL GSM CONTROLLER V1.0 MANUAL

200 User GSM Switch - 1000 Event Log - Unauthorised Alerts - GSM Intercom

Introduction...

b) * Enable CLIP 'Authorised Callers Only - 200 Users' (CLPEN=1) (default setting).....8 c) Enable CLIP 'Any Caller Mode' - Unlimited Users (CLPEN=2).............................8 d) Choose which Output to Switch (CLPOU=1) ................................................8 e) Link the CLIP feature to an actived Input in order to enable (CLPI=0).................8 f) Retrieve the 200 User List in Full or in Parts to Delete or Add New Users (PCLP=xy,xx) ........................................................................................8 g) Add or delete Authorised Callers (CLP1 - CLP200).........................................9

  1. SET UP TO 5 AUTHORISED ADMINISTRATORS FOR PROGRAMMING & ALERTS ..........10

    a) Add or delete Authorised Administrator Mobile Numbers (TN1 - TN5) ............... 10 b) Set up Active Authorised Administrator Mobile Numbers (SL) ......................... 10 c) Link Events from Inputs or Preset Events to Authorised Administrators (LN1 -
    LN6) ................................................................................................ 11

  2. CALLER ID EVENT LOG ............................................................................11

    a) Set up the Self Updating Clock (UDC) ..................................................... 11 b) Change the Event Log Buffer from Auto Clear to Manual Clear & Send Alert at 900 events (ALC) ...................................................................................... 12 c) Request Event Log by SMS Text Message (PLOG)......................................... 12 d) Set the default amount of Events to receive by SMS Text Message (LOGN) ......... 12 e) Request how many Events are in the Current Event Log (PLOG=?) ................... 12 f) Request Event Logs between a set range of Total Events (PLOG=xy,xx) ............. 12 g) How to find the most Recent Events....................................................... 13 h) After Retrieving & Saving the Event Log to your PC, Erase completely by SMS Text (LCLR).............................................................................................. 13

  3. OUTPUTS FOR SWITCHING DEVICES ............................................................13

    a) Request Current Output Switch Status Pulse, Latch, Timed, 1st call ON / 2nd OFF (POS) ............................................................................................... 13 b) Request Current Output State (PORC) .................................................... 13 c) Change Output Switching Status Pulse, Latch, Timed, 1st call ON / 2nd call OFF (OS1 & OS2) ....................................................................................... 13 d) Change an Output Contact between Open [going closed] or Closed [going open] (OP1 & OP2)....................................................................................... 14 e) Make an Output Directly Switch when an Input 1 is Activated (OD1) ie: press to exit input ............................................................................................... 14 f) Make an Output Directly Switch when an Input 2 is Activated (OD2) ie: siren/ flashing beacon................................................................................... 14 g) Make an Output Directly Switch when a GSM Network Error occurs (OD3) .......... 14 h) Make an Output Directly Switch when an Unauthorised Caller calls GSW2 (OD4) .. 15 i) Control an Output by SMS Text Message (ORC) ........................................... 15

  4. SET UP INPUTS FOR SMS TEXT ALERTS or GSM INTERCOM CALL BUTTONS ............. 15

    a) Change how inputs trigger & whether an SMS text is sent to notify 'input restored' (IN1 & IN2) ........................................................................................ 15 b) Change the time delay before SMS text alerts are sent after inputs activated (ID1 & ID2) ................................................................................................. 15 c) Request the current Device labels for the SMS Text Alerts (P#)....................... 16 d) Change the label printed on the SMS text alert sent related to Device (#0LOCATION) .................................................................................... 16 e) Change the label printed on the SMS text alert sent related to Input 1 (#1INPUT

    1) ................................................................................................... 16 f) Change the label printed on the SMS text alert sent related to Input 2 (#2INPUT
    2) ................................................................................................... 16

  5. GSM INTERCOM SET UP............................................................................16

    a) Enable the Inputs to be used as GSM intercom Call Buttons (WMOD) ................ 18 b) Set Up the Numbers called by Call Button 1 (PDEA) .................................... 18 c) Set Up the delay timer before dialing the next number (RTNA) ...................... 18

d) Set Up the Numbers called by Call Button 2 (PDEB) .................................... 19 e) Set Up the delay timer before dialing the next number (RTNB) ...................... 19 f) Door Release ................................................................................... 19

  1. MISCELLANEOUS PARAMETERS (SIM, Device & GSM Intercom) ............................ 19

    a) General Settings (defaults shown) ......................................................... 19 b) SIM Card / Mobile Network Settings (defaults shown) .................................. 20 c) Device Reset (defaults shown) .............................................................. 21

  2. SMS TEXT PRINT COMMANDS (automatically prompt GSW2 for current settings) ..... 21

    a) Receive all Current Parameters Set (PALL)............................................... 21 b) Receive all Current Caller ID Control Settings, Authorised Callers & Vacant Slots (PCLP).............................................................................................. 21 c) Receive all Authorised Administrator Mobile Numbers and/or Vacant Number Slots (PTN) ............................................................................................... 21 d) Receive the Security Level ie: Which Administrators are allowed to program GSW2 (PSL)................................................................................................ 21 e) Receive which alerts are 'Linked' to which Authorised Administrators (PLN) ....... 22 f) Receive Input configuration ie: How long they must be active before alerts are sent (PID)................................................................................................ 22 g) Receive Output configuration ie: How outputs are set to switch; pulse, latch,

    timed (POS) ....................................................................................... 22 h) Receive Current Output States ie: Are they active or not (PORC) .................... 22 i) Receive Direct Output configuration ie: How outputs switch on Input / Event activity (POD)..................................................................................... 22 j) Receive programmed labels for the device Name / Location & Inputs (P#) ......... 22 k) Receive the Current Settings of the Miscellaneous Parameters (PPA)................ 22 l) Receive the remaining SIM card credit (PCC1)............................................ 22 m) Receive the Current Settings for the GSM Intercom Feature - BUTTON 1 (PDEA) . 22 n) Receive the Current Settings for the GSM Intercom Feature - BUTTON 2 (PDEB) .. 23

  3. LED DISPLAY ........................................................................................23

    1. BLUE GSM Network Signal Strength (1 Flash = Low Signal / 5 Flashes = Maximum Signal) ................................................................................. 23

2. RED Device / Connection / Network Fault ........................................... 23 3. YELLOW GSM Network (1 Flash/sec. = Registering & 1 Flash per 5 sec. = On Network) .......................................................................................... 23

14. TROUBLESHOOTING................................................................................ 23

a) Device won't connect to the GSM network ............................................... 23 b) General audio interference during intercom calls....................................... 23 c) Whistling or interference all the time or during a call................................. 24 d) Device won't respond and blue LED is solid ............................................. 24 e) SMS Programming won't work .............................................................. 24 f) Voicemail cuts in before my intercom call transfers to the second number ........ 24 g) Speaker Level is too low / high............................................................. 24 h) Red LED is solid ............................................................................... 24 i) Red LED is Flashing ........................................................................... 24 j) If your issue is not listed here .............................................................. 25

QUICK START GUIDE (start here for the most basic set up)
For those that want the most simple of features, the device is set up with default settings that

more than likely suit your task. Get up & running within minutes.
Add additional features by following the manual to set other Security features & Authorised Users.

page4image16960

d) Set a User Phone Number to Test...

The device is set by default to switch Relay Output 1 & by Authorised Users only so you must first add one.
- If using an 02 UK PAYT SIM card, send this text message first before any other: ;+SPO=10;

Now Send this SMS text message...

;+CLP1=XXXXXXXXXXX; where XXXXXXXXXXX = the authorised User phone number you will use to call GSW2.

e) Call GSW2 to test the output...

Dial the number of the SIM card in GSW2 from the number just programmed above. It will recognise the number and switch the output. You will here a tone and a click.

GUIDE TO SMS TEXT MESSAGE PROGRAMMING

The unit can be completely controlled & managed by SMS Text Messages. This is the most convenient method for End Users and can be carried out from anywhere in the world instantly.

a) Benefits of GSW2 SMS Text Based Programming

page5image20864 page5image21024 page5image21344 page5image21504 page5image21664 page5image21824 page5image21984 page5image22144 page5image22304 page5image22464 page5image22624 page5image22784 page5image22944

GSW2 TECHNICAL OVERVIEW
Technical details about the hardware, terminal layouts, technical capability & requirements. a) Hardware Description & Connection Diagram

page6image12000

GUIDE TO PC PROGRAMMING VIA USB

The unit can be programmed by PC using optional software available for download here

a) PC Programming using any Windows PC

  1. You will need to plug the unit into your PC using a USB to mini USB cable

  2. You must first install the Driver for the GSM Controller mini-USB port DOWNLOAD THE USB

    DRIVER

  3. Check which COM port your GSM Controller is connected to in your PC Control Panel (Start > Control Panel > Performance & Maintenance > System > Hardware > Device Manager > Ports)

  4. PC Programming Software available from your Supplier MORE INFO HERE

CALLER ID DEVICE CONTROL [CLIP] mobile phone dialing in to switch GSW2

Set up GSW2 to control your gate, barrier, heating or whatever else you choose to control. The feature can be configured in 2 work modes; 'Authorised Caller' or 'Any Caller'. Authorised Caller is the default setting.

page7image33224 page7image33384 page7image33808 page7image34232

a) Disable the CLIP Feature (CLPEN=0)

To temporarily disable the CLIP feature, send text: ;+CLPEN=0; - This will not affect any Authorised Callers already set up

b) * Enable CLIP 'Authorised Callers Only - 200 Users' (CLPEN=1) (default setting)

To enable the 'Authorised User List', send text: ;+CLPEN=1; - Only Users on the list can switch the device.

c) Enable CLIP 'Any Caller Mode' - Unlimited Users (CLPEN=2)

To enable 'Any Caller Mode' , send text: ;+CLPEN=2;
- This mode is less secure as any incoming call will switch the device.

d) Choose which Output to Switch (CLPOU=1)

The CLIP feature can be used with only one Output. GSW2 V.2 will have dual output switching on separate numbers.
To enable output 1, send text:
;+CLPOU=1;
To enable output 2, send text: ;+CLPOU=2;

e) Link the CLIP feature to an actived Input in order to enable (CLPI=0)

The CLIP feature can be used in conjunction with an Input which means the Input must be active before teh CLIP feature can operate. An example is a ground induction loop that must be driven onto before the barrier/gate or device can be activated. This prevents remote control of the device unless another physical parameter is met.

i.) If Input 1 is to be used to arm the CLIP feature, send SMS text: ;+CLPI=1; (note: ;LN1=0;) - The device can only be switched by the CLIP feature if Input 1 is active

ii.) If Input 2 is to be used to arm the CLIP feature, send SMS text: ;+CLPI=2; (note: ;LN2=0;) - The device can only be switched by the CLIP feature if Input 1 is active

iii.) To enable the CLIP feature without activating an Input, send SMS text: ;+CLPI=0; - The device can be switched by the CLIP feature as normal without any Input connection

f) Retrieve the 200 User List in Full or in Parts to Delete or Add New Users (PCLP=xy,xx)

You can retrieve all or some of the Authorised Callers by sending SMS text message: ;PCLP=xy,xx; (where xy,xx = the range between User positions in the device memory.

The device will reply with your selected range of User slots to show the vacant and occupied slots.

Tip: Allocate sections of the CLIP User memory to groups of Users for quick retrieval by SMS text message.

example: CLP1 - CLP50 (Internal Staff) CLP51 , CLP100 (Drivers) CLP101 - CLP150 (Visitors) etc...

Tip: If you want to find the List position of an 'existing Driver' in order to delete the phone number, or just 'add a new Driver' to the list, you request only that section of the User List with SMS text message: ;PCLP=51,100;
- only that section will be returned with currently occupied positions and any free positions.

To Edit the User List:
1.
Select 'Forward Message' in your mobile phone text options and choose the SIm card number of GSW2
2. Edit the message received to either 'add or delete' the Users as required
3. Send the edited message back to the device

g) Add or delete Authorised Callers (CLP1 - CLP200)

To add 'Authorised Callers' to the 200 User list, you must enter the phone number in a vacant slot in the list. By SMS Text message, you can request individual slots or a range of any 2 numbers between 1 - 200.

ie: Retrieve the first 20 slots from the list, send text: ;PCLP=1,20; ie: Retrieve more slots from the list, send text: ;PCLP=21,50;
... and so on

Depending on how many User slots you request, you will receive 1 or multiple replies including the current CLIP setup as above and the Occupied & Vacant for the selected range.

Example:

;PCLP=1,3;

- You will receive a reply as follows ;CLPEN=1;CLPOU=1;CLP1=;CLP2=;CLP3=;

1. Select 'Forward Message' in your mobile phone text options.

2. Edit the message as required by adding the numbers you want to add. Note the + symbol. This means a reply confirmation will be returned. Omit the + to disable the reply: ;+CLPEN=1;CLPOU=1;CLP1=077965124589;CLP2=02074561254;CLP3=02074561253;

3. Send the message back to the SIM card in the device to update the settings.

h) To delete Authorised Users

Remove the number between the = and ; symbols that you want to delete. Note the + symbol. This means a reply confirmation will be returned. Omit the + to disable the reply: ;+CLPEN=1;CLPOU=1;CLP1=077965124589;CLP2=;CLP3=;

i) Automatic Re-CLIP function (auto close pulse for gates not set to auto close) About: After a CLIP command (caller ID incoming call) is received, GSW2 switches the output as set.

If teh auto re-clip feature is set, GSW2 looks at the input number set in CLPRI and will automatically make a second pulse of the same output as long as this input isn't active.

The time window for this function is set using CLPRT. Ie: If the input remains active for longer than this

time, the GSW2 will not automatically repulse the output.

Why?

If an automatic gate is set as 'press to open' & 'press to close', this function acts as an automatic secong pulse to close the gate without actually having to press anything. It checks the input to make sure it's safe first. Your safety beam contact would be wired through the GSW2 input so GSW2 can check if they are obstructed or not before sending the close pulse. If the featre times out, GSW2 does not switch.

;CLRPI=X; Input number for auto reclip function (X = the input number ie: 1 or 2)
;CLPRT=XX; Time window (XX = the time frame in seconds within which the GSW2 will check the input)

SET UP TO 5 AUTHORISED ADMINISTRATORS FOR PROGRAMMING & ALERTS

Authorised Administrators are 'authorised' to program the device by SMS text & also receive SMS text alerts for various event as set by parameter LN. By 'linking' events (LN1 - LN5) to Authorised Administrators, you can select certain Administrators to receive alerts for some or all events.

a) Add or delete Authorised Administrator Mobile Numbers (TN1 - TN5)

Send this SMS text message to receive a list of Current Authorised Administrators: ;PTN; - You will receive a reply: ;TN1=;TN2=;TN3=;TN4=;TN5=;

To change the setting, send: ;TN1=07798765140;TN2=;TN3=;TN4=;TN5=;
b) Set up Active Authorised Administrator Mobile Numbers (SL)

You can allow any mobile number to program GSW2 by SMS text by leaving it as the default setting. If you want to restrict programming to a limited number of Administrators, send this SMS text message to receive the currently set Security Level: ;PSL;
- You will receive a reply: ;SL=0;

Reply to the message and set one of the following parameters to allow numbers in your Authorised Administrator list to program the GSW2 exclusively.

To change the setting, send: ;+LNx=y;
Where 'x' = The 'Alert Link' number as above (LN1 - LN6)
Where 'y' = The 'Authorised Administrator' number/s as detailed above (TN1 - TN5) Note: You can add more than 1 Adminsitrator: Just add the numbers ie:
;+LN1=123;

CALLER ID EVENT LOG

Calls made to the SIM card in GSW2 are Events and are logged by Date, Time, Phone Number, Output & Authorised / Non-Authorisd Status. Activity on the Inputs is also logged by Active & Restored Status. Up to 1000 events are logged.

The Event Log can be requested in various ways by both SMS Text Message & PC via the onboard mini USB port to ensure quick and simple retreival of Events within the entire Log.

a) Set up the Self Updating Clock (UDC)

GSW2 will send itself an SMS text message after it loses power to refresh the clock with the Network Operators Clock.

To set the feature, enter the mobile number of the SIM card you have put into GSW2 by sending this SMS text: ;+UDC=XXXXXXXXXXX;

b) Change the Event Log Buffer from Auto Clear to Manual Clear & Send Alert at 900 events (ALC)

The Event Log is full at 1000 Events. By default, GSW2 will automatically clear the event log when it is full. You can change this for 'Manual Log Clear' by sending an SMS text message.

;+ALC=0; (Event Log will send an SMS text alert when 900 Events are in the device - User must clear*) ;+ALC=1; (Event Log will automatically clear after 1000 Events are in the device) DEFAULT SETTING

*With Automatic Log Clear set, you can still request the event log at any time and retrieve log events. If you retreive log events regularly and save them, you can use the manual Log clear at any time by sending SMS text message: ;LCLR;

The Event Log will then start from 0001 again.

c) Request Event Log by SMS Text Message (PLOG)

To return the Events by either SMS Text Message, first you should set the default amounts of events to be returned. Note by SMS text message, each log is sent in 1 message so 5 events will send 5 messages.

g) How to find the most Recent Events

If you want to know the most recent events, first you need to check how many Events are currently in the device. Send the SMS text message: ;PLOG=?;
- The reply will be: Num. of LOG Entries:95 (95 is an example only)

From this point you know you have '95' events in memory so send this SMS text message to retrieve the most recent 5 events: ;PLOG=90,95;

h) After Retrieving & Saving the Event Log to your PC, Erase completely by SMS Text (LCLR)

Send this SMS text message to clear all events and start a fresh Event Log: ;LCLR; OUTPUTS FOR SWITCHING DEVICES

GSW2 has 2 outputs which switch in the same way however the outputs are completely different. Output 1 is a voltage free contact which is set open by default. It closes when it is activated and makes a voltage free connection between the 2 terminals marked 'relay'.

Output 2 is different in the sense that it is not voltage free when it is activated. It supplies 300mA max. from the 2 terminals marked Out 2 GND & Out 2 +12VDC. It supplies a voltage near to 12VDC depending on your input supply voltage and is designed to power low consumption 12VDC devices such as relays.

a) Request Current Output Switch Status Pulse, Latch, Timed, 1st call ON / 2nd OFF (POS) Send this SMS text message to receive the current configuration of each output: ;POS;

- You will receive a reply like this: ;OS1=5;OS2=5; b) Request Current Output State (PORC)

Send this SMS text message to receive the current state of each output: ;PORC; - You will receive a reply like this: ;Output 1=OFF;Output 2=OFF;

c) Change Output Switching Status Pulse, Latch, Timed, 1st call ON / 2nd call OFF (OS1 & OS2)

By default, both outputs are set 'Normally Open' & will pulse closed for 5 seconds. Both outputs can be configured to switch in various ways to suit multiple applications.

d) Change an Output Contact between Open [going closed] or Closed [going open] (OP1 & OP2) The default setting for both outputs is N/O or 'Normally Open' [Open switch going

closed].1

i) To make an Open switch close when activated (DEFAULT)

To change Output 1, send SMS text message: ;+OP1=0; To change Output 2, send SMS text message: ;+OP2=0;

i) To make a Closed switch open when activated

To change Output 1, send SMS text message: ;+OP1=1; To change Output 2, send SMS text message: ;+OP2=1;

e) Make an Output Directly Switch when an Input 1 is Activated (OD1) ie: press to exit input

Outputs can be set to switch immediately as inputs are triggered. This is useful for 'press to exit'. - To switch Output 1 when Input 1 is activated, send SMS text message: ;+OD1=1;
- To switch Output 2 when Input 1 is activated, send SMS text message: ;+OD1=2;

To see how to configure Inputs see the Inputs section of this manual.

f) Make an Output Directly Switch when an Input 2 is Activated (OD2) ie: siren/flashing beacon

Outputs can be set to switch immediately as inputs are triggered. This is useful for 'alarm notification'. - To switch Output 1 when Input 2 is activated, send SMS text message: ;+OD2=1;
- To switch Output 2 when Input 2 is activated, send SMS text message: ;+OD2=2;

To see how to configure Inputs see the Inputs section of this manual.

g) Make an Output Directly Switch when a GSM Network Error occurs (OD3)

Outputs can be set to switch immediately if a Network Fault occurs.
- To switch Output 1 when a Network Fault occurs, send SMS text message:
;+OD3=1; - To switch Output 2 when a Network Fault occurs, send SMS text message: ;+OD3=2;

To see how to also send an SMS text Alert to Authorised Administrators see the section of this manual.

h) Make an Output Directly Switch when an Unauthorised Caller calls GSW2 (OD4)

Outputs can be set to switch immediately if an Unauthorised Caller dials the GSW2. This is useful to fit a siren or flashing beacon to Output 2 which sounds/shows as a warning alarm.
- To switch Output 1 when a Network Fault occurs, send SMS text message:
;+OD4=1;
- To switch Output 2 when a Network Fault occurs, send SMS text message: ;+OD4=2;

i) Control an Output by SMS Text Message (ORC)

- To switch Output 1 ON by SMS text message, send SMS text message: ;+ORC1=1; - To switch Output 1 OFF by SMS text message, send SMS text message: ;+ORC1=0; - To switch Output 2 ON by SMS text message, send SMS text message: ;+ORC2=1; - To switch Output 2 OFF by SMS text message, send SMS text message: ;+ORC2=0;

Note: If you have the Output Status (OS) set to '1', the contact is latching. In this case, switch the output OFF using the OFF commands above. If you have the Output Status (OS) set to 'any other number', it is a pulse time contact so you don't need to switch it off. It switches off after yoiur chosen time.

SET UP INPUTS FOR SMS TEXT ALERTS or GSM INTERCOM CALL BUTTONS

The Inputs are used for 2 functions. SMS Text Alarms & Call Buttons. With any type of sensor ie: door contacts / motion / temperature / water level etc, connected to the inputs, SMS Text Alerts can be sent to Authorised Administrators as set by the Links (LN)

a) Change how inputs trigger & whether an SMS text is sent to notify 'input restored' (IN1 & IN2)

IN = 0 : Normally Open - triggered by linking Input to a negative voltage (GND) DEFAULT
IN = 1 : Normally Close - breaking a closed voltage loop (between Input & +12VDC or GND) IN = 2 : Normally Open - triggered by linking Input to a positive voltage (+12VDC)
IN = 3 : not used
IN = 4 : [Same as IN = 0] + input restored SMS text sent when Input is not active anymore IN = 5 : [Same as IN = 1] + input restored SMS text sent when Input is not active anymore IN = 6 : [Same as IN = 2] + input restored SMS text sent when Input is not active anymore

- To change Input 1 Status, send SMS text message: ;+IN1=x; where 'x' = the status number (0-6)
- To change Input 2 Status, send SMS text message:
;+IN2=x; where 'x' = the status number (0-6)

b) Change the time delay before SMS text alerts are sent after inputs activated (ID1 & ID2)

Change the delay time in which SMS text alerts are sent. By default they send immediately when the input is activated. You can set a delay so that the input must be activated for a time period before the alert is sent:
- To delay Input 1 alerts, send SMS text message:
;+ID1=xx; where 'xx' = the delay time in seconds

- To delay Input 2 alerts, send SMS text message: ;+ID2=xx; where 'xx' = the delay time in seconds

c) Request the current Device labels for the SMS Text Alerts (P#)

To return the current device labels for location & inputs, send this SMS text message: ;P#; - You will receive a reply like this: ;User Location, Input 1, Activity in Progress!

d) Change the label printed on the SMS text alert sent related to Device (#0LOCATION)

To change the label for Device/User Location, send this SMS text message: ;+#0MY_HOUSE=1; - The Name label can be changed up to a maximum of 14 characters including spaces.

e) Change the label printed on the SMS text alert sent related to Input 1 (#1INPUT 1)

To change the label for Input 1, send this SMS text message: ;+#1SENSOR_OUT=1;
- The Name label can be changed up to a maximum of 14 characters including spaces.

f) Change the label printed on the SMS text alert sent related to Input 2 (#2INPUT 2)

To change the label for Input 2, send this SMS text message: ;+#2SENSOR_TWO=1;
- The Name label can be changed up to a maximum of 14 characters including spaces.

GSM INTERCOM SET UP

By enabling Inputs 1 and/or 2 as Call Buttons, a preset list of phone numbers can be called one after the other for 2 way communication. With a preset trip delay between the numbers, Voicemail can be prevented from interupting the calling process.

Step 1: Connect power input, call button, 12VDC OUT & audio wires as shown. They are labeled the same on the call point & GSW2 so just connect like to like.

page18image656

Step 3: Program the numbers by SMS text messages as follows

a) Enable the Inputs to be used as GSM intercom Call Buttons (WMOD)

You must enable the Inputs as Call Buttons to use the intercom feature. Wire call button into Input 1 or 2 then...

To enable Input 1 as a call button Input, send Text: ;+WMOD=1;
To enable Input 2 as a call button Input, send Text: ;+WMOD=2;
To enable both Input 1 & 2 as a call button Inputs, send Text: ;+WMOD=12;

b) Set Up the Numbers called by Call Button 1 (PDEA)

To retrieve the current settings, send Text: ;PDEA; - You will receive a reply as follows: ;ATN1=;ATN2=;ATN3=;ATN4=;ATN5=;RTNA=15;

Select 'Forward Message' from your mobile phone text options & choose the intercom's SIM No.

Edit the message as required by adding the the numbers you want the intercom to call in order starting at ATN1 as follows:
;+ATN1=077965124589;ATN2=02074561254;ATN3=;ATN4=;ATN5=;RTNA=15;

c) Set Up the delay timer before dialing the next number (RTNA)

The time delay is set at 15 seconds by default. If you want to change this time up or down, send text: ;+RTNA=xx; where 'xx' = the time in seconds.

d) Set Up the Numbers called by Call Button 2 (PDEB)

To retrieve the current settings, send Text: ;PDEB; - You will receive a reply as follows: ;BTN1=;BTN2=;BN3=;BTN4=;BTN5=;RTNB=15;

Select 'Forward Message' for your mobile phone text options.
Edit the message as required by adding the numbers you want the intercom to call in order as follows:

;+BTN1=077965124589;BTN2=02074561254;BTN3=;BTN4=;BTN5=;RTNB=20;

e) Set Up the delay timer before dialing the next number (RTNB)

The time delay is set at 15 seconds by default.
If you need to change this up or down, send text:
;+RTNA=xx; where 'xx' = the time in seconds.

f) Door Release

The User hangs up the call & speed dials the GSW2 back from an authorised phone. When the GSW2 is called back, an audible beep is played from the call point speaker as the door unlocks. The entry event is logged.

i) The number of the SIM card in GSW2 should be set as a preset 1 press speed-dial on the User's phone ii) The preset speed-dial button can be used for door release at any time

MISCELLANEOUS PARAMETERS (SIM, Device & GSM Intercom)
The device has various parameters that can be customised to suit the User or application. Not all are

relevant to every application so they are grouped into categories.

a) General Settings (defaults shown)

MUT=0 (Silent or Ringing Sound during intercom call connection) - Send SMS text: ;+MUT=1; to mute the ringing sound
- Send SMS text:
;+MUT=0; to enable the ringing sound

MIC=0 (Call Point Microphone Level 0 - 15)
- Send SMS text: ;+MIC=x; where x = 1 - 15 to increase the MIC level

SPK=80 (Call Point Speaker Level 75 - 100 max.)
- Send SMS text: ;+SPK=xxx; where x = 75 - 100 to increase the SPK level

LOT=60 (Line Open Time - to limit the length of intercom calls 0 - ~ seconds) - Send SMS text: ;+LOT=90; to increase the line open time
- Send SMS text:
;+LOT=45; to decrease the line open time

ADF=90 (Automatic Dial - Calls Administrator 1 at interval to prevent prepay SIM card expiry 0 - ~ days) - Send SMS text: ;+ADF=180; to increase the days before automatic calling
- Send SMS text:
;+ADF=75; to decrease the days before automatic calling

MRT=1 (Mute Tone - Disables beep when outputs are activated) - Send SMS text: ;+MRT=0; to disable the output activated beep - Send SMS text: ;+MRT=1; to enable the output activated beep

b) SIM Card / Mobile Network Settings (defaults shown)

SPO=1 (If using an 02 UK PAYT SIM card this parameter must = 10 - Do not change if not using 02 UK prepaid)
- If using an 02 PAYT SIM card, send this text message first before any other: ;+SPO=10;

CC1= (SIM Credit Checking - The following examples are for UK 02 & Vodafone PAYT networks only) - To set up 02 UK PAYT SIM card, send SMS text: ;CREF.=1;CC1=*#10#;
- To set up 02 IRELAND PAYT SIM card, send SMS text: ;CREF.=1;CC1=*#100#;
- To set up Vodafone PAYT SIM card, send SMS text: ;CREF#=2;CC1=*#1345#;

Contact Support regarding this feature on other networks. Not all networks support credit checking SMS code.

LCV=4 (Low Credit - If the CC1 & CREF above are set correctly, alerts will be sent when credit reaches £x)
- Send SMS text: ;+LCV=3; to set the level of whole pounds your credit must reach before alerts are sent

- Alerts will be sent at intervals of 1 in your currency until a minimum of 1 is reached. Alerts stop at 1 to prevent last credit being used.

TST=24 (Set in Hours, a test message is sent at this interval to check the SMS Text Alerts are operational)
- Send SMS text: ;+TST=168; to set the test alert for every 7 days

ALC=1 (Auto Log Clear - When GSW2 reaches 1015 events, it automatically clears the Log)
- Send SMS text: ;+ALC=0; Manual Log Clear (an SMS text alert will be sent to TN1 at 900 & again at 1015 events)
- Send SMS text:
;+ALC=1; to enable Automatic Log Clear

When Authorised Administrator (TN1) receives the 'event log full' alert, make a back up of the required log data either by SMS text or PC and then manually erase the entire Event Log memory by sending SMS text: ;LCLR;

LNG=0 (Language - 0 = English)
- Send SMS text: ;+LNG=x; where 'x' = number 0 - 7 for various languages.

English=0
Italian=1
Slovenian=2
Croatian=3
Dutch=4
French=5 (not supported) Spanish=6 (not supported) German=7

SDCLR (Erase all parameters from SIM card. Returns all parameters back to default)
- Send SMS text:
;+SDCLR;
(IMPORTANT: WAIT AT LEAST 5 MINUTES AFTER SENDING THIS COMMAND. DO NOT SWITCH OFF OR CONNECT / DISCONNECT ANYTHING)

The RED LED will flash while the erasing is in progress. The GSW2 will automatically reset at the end and when the BLUE LED flashes again the device is ready for re-programming.

c) Device Reset (defaults shown)

MRES (Manual Reset - to manually reboot the GSM module only - will not erase settings)
- Send SMS text: ;MRES; to manually reboot the GSM module and re-register the SIM card on the network

SSRES (Manual Reset - to manually reboot the GSM module & processor - will not erase settings)
- Send SMS text: ;SSRES; to manually reboot the GSM module & micro-processor. This completely restarts the device as it would if it was powered down and back on; without actually having to switch the power off.

ARST=168 (Automatic Interval Reset in hours to automatically reboot GSM module - will not erase settings)
- Send SMS text: ;+ARST=90; to reboot the GSM module and re-register the SIM card on the network

SMS TEXT PRINT COMMANDS (automatically prompt GSW2 for current settings)
GSW2 has a unique SMS text prompt system whereby you can request all or certain parameters before

making any changes. You may need to adjust a User or setting quickly. This is the best way to do it.

After receiving the information, select 'forward message', make your changes to the information & send it back to GSW2. The unit will be instantly updated. It's a good idea to include the '+' in the command sent ie: ;+CLP1=......; or alternatively you can send the same 'PRINT' command again to retrieve the data to see if you changes were applied.

a) Receive all Current Parameters Set (PALL)

- Send this SMS text: ;PALL;
Note: If you send ;PALL; by SMS, you will receive at least 30 text messages with the settings. This command is best used by PC & normally by the Installer for the purpose of fault finding within the parameters set.

b) Receive all Current Caller ID Control Settings, Authorised Callers & Vacant Slots (PCLP)

- Send this SMS text: ;PCLP;
c) Receive all Authorised Administrator Mobile Numbers and/or Vacant Number Slots (PTN) - Send this SMS text: ;PTN;
d) Receive the Security Level ie: Which Administrators are allowed to program GSW2 (PSL)

- Send this SMS text: ;PSL;

e) Receive which alerts are 'Linked' to which Authorised Administrators (PLN)

- Send this SMS text: ;PLN;
f) Receive Input configuration ie: How long they must be active before alerts are sent (PID) - Send this SMS text: ;PID;

g) Receive Output configuration ie: How outputs are set to switch; pulse, latch, timed (POS)

- Send this SMS text: ;POS;
h) Receive Current Output States ie: Are they active or not (PORC)
- Send this SMS text: ;PORC;
i) Receive Direct Output configuration ie: How outputs switch on Input / Event activity (POD) - Send this SMS text: ;POD;
j) Receive programmed labels for the device Name / Location & Inputs (P#)
- Send this SMS text: ;P#;
k) Receive the Current Settings of the Miscellaneous Parameters (PPA)

PPA will return a list of general parameters; UDC (self clock update), HTN (not relevant), SCV (Prepaid SIM card validity period), TST (Test SMS), MNF (not relevant), MIC (microphone level), SPK (speaker level), LCV (low credit SMS limit), LNG (not relevant), LOT (line open time), LOGN (event log limit by SMS), LOGI, ALC, ADF, ARST, CREF, CTIME, OP1, OP2, BUZ, MRT, SPO

- Send this SMS text: ;PPA;
l) Receive the remaining SIM card credit (PCC1)

- Send this SMS text: ;PCC1;
- This feature will only work if the paremeters ;CC1; & ;CREF; are set according to the SIM card being used. 02 & VF UK are shown below:
- To set up 02 UK PAYT SIM card, send SMS text: ;CREF.=1;CC1=*#10#;
- To set up 02 IRELAND PAYT SIM card, send SMS text: ;CREF.=1;CC1=*#100#;
- To set up Vodafone PAYT SIM card, send SMS text: ;CREF#=1;CC1=*#1345#;

No other UK Networks are supported. Contact Support for more info.

m) Receive the Current Settings for the GSM Intercom Feature - BUTTON 1 (PDEA)

- Send this SMS text: ;PDEA;

n) Receive the Current Settings for the GSM Intercom Feature - BUTTON 2 (PDEB)

- Send this SMS text: ;PDEB;

LED DISPLAY

The LED's are to indicate what is happening on the device at any given time.

1. BLUE GSM Network Signal Strength (1 Flash = Low Signal / 5 Flashes = Maximum Signal)

If the Blue is on solid, the device is not connected to the network. You will find that red is also on or flashing on/off. This indicates something is not right with the network and could be antenna, or SIm card related.

2. RED Device / Connection / Network Fault

Red will flash during start up to indicate the processor is reading the SIM card. It will also flash if the device is erasing data when prompted. It should not be on at all during normal operation. If the Red is solid or flashing at any time other than the initial 30 - 60 seconds after power up while the device logs onto the network; you have a fault somewhere.

Red indicates something is not right in general and could be to do with the network, antenna, SIM card, connections or hardware damage. Check carefully starting with your wiring connections. Then try the device in a different 'open air' location. Failing that try a differnt network SIM card. Visually inspect the hardware and look for any obvious damage or foreign objects on the PCB.

3. YELLOW GSM Network (1 Flash/sec. = Registering & 1 Flash per 5 sec. = On Network)

The Yellow is only related to the Network initial registration & then reporting that the device is currently on the network. If the Yellow is not flashing once every 5 seconds, it is not on the GSM Network.

TROUBLESHOOTING

Check the status of the LED's first and check the LED descriptions to provide a general idea of what to look at first.

a) Device won't connect to the GSM network

- Move the GSW2 to another location
- Try another SIM card or check the SIM card PIN code request is disabled - Connect the optional external antenna
- Check supply voltage is sufficient

b) General audio interference during intercom calls

- Make sure you have all cable screens (metal bare wire around coloured cores) connected to GND

- The bare wire screen of the 2 pair audio cable must be connected to GND both ends
- Use a Switch mode 12VDC regulated power supply 1 amp minimum.
- Don't run other equipment on the same power supply as the GSM intercom
- Keep the intercom audio cable & antenna away from mains power cables as best as possible - Keep the antenna outside any metal enclosures or fit an optional external antenna

- Connect any metal panel enclosures to GND especially if mounted to a steel post - Check the audio terminal connections are not loose (yellow, white, brown, green) - Lower the microphone level on the GSM call panel

c) Whistling or interference all the time or during a call

- Lower the microphone level on the GSM call panel

d) Device won't respond and blue LED is solid

- GSM Network Signal issue
- SIM card not inserted correctly
- Try different SIM card
- Check antenna connection
- Make sure antenna is not inside a metal enclosure

e) SMS Programming won't work

- Check SL (Security Level). The number you are sending the commands from may not be authorised - Check SIM card is on the network (see LED display)

f) Voicemail cuts in before my intercom call transfers to the second number

- Change RTNA (button1 ) or RTNB (Button 2) to a higher number. This will make the call ring longer.

g) Speaker Level is too low / high

- Adjust SPK up or in Miscellaneous Parameters

h) Red LED is solid

- Check connections and polarity on GSM controller & intercom interface PCB - Check PCB components visually to locate obvious damage
- Check power supply input voltage is sufficient

i) Red LED is Flashing

- Fit external antenna
- Relocate controller
- Change Network SIM card

 

 

 

BASIC MANUAL & QUICK START GUIDE *** FOR HASSLE FREE SET UP, START HERE ***

  1. Read this installation manual first...

  2. Install 12V wiring from power source to intercom location

  3. Mount antenna up high away from speaker with gold connector at intercom location.

  4. Mount intercom over 12V & antenna wires.

  5. Fit SIM card as detailed below. Insert SIM

    carefully as SIM holder is fragile if forced!

WIRING

Wiring is minimal. Apart from 12V power to intercom & door release wires, there is no other required wiring

Do not use the shown wiring for an electric lock if it needs more than 300mA. Use separate power source. For gates & barriers connect as shown on output 1.

FITTING THE SIM CARD

Insert the SIM card gold contacts down and with the cut off to the RHS as shown on the diagram above. Insert SIM carefully. It will NOT break unless forced!

PROGRAMMING SETTINGS BY SMS (TEXT) Note: You can send individual commands like ;ETN1=07796176545; or together in one long text as shown. Don't exceed 160 characters.

IMPORTANT: If using 02 or Orange PAYG SIM send this FIRST: ;+SPO=10; If you don't, your settings will be lost on power down.

Set numbers to call (in order 1 - 5):

;+ETN1=07796176545;ETN2=xxxxxxxxxx;ETN3= xxxxxxxxxx;ETN4= xxxxxxxxxx;ETN5=xxxxxxxxxx;

Set delay time (before calling next number):

;+RTNE=20;

Change speaker level (default is 10 max is 15):

;+SPK=15;

Set Authorised Caller ID Users (up to 100):

;+CLP1=07796176545;CLP2=xxxxxxxxxx;CLP3=xxxxxxxxxx;CLP4= xxxxxxxxxx;CLP5=xxxxxxxxxx;
CLP6= xxxxxxxxxx;CLP7.........(up to 100)

Set output switching configuration:
Output 1
(3 second pulse default = ;+OS1=3; ) Change to 5 second pulse ;+OS1=5;
Change to latching (on / off): ;+OS1=1;

Output 2 (3 second pulse default = ;+OS2=3; )
Change to 5 second pulse ;+OS2=5;
Change to latching (on / off): ;+OS2=1;
First call on / Second call OFF: If you Send ;+OS1R=1; (output 1) or ;+OS2R=1; (output 2), The output will be set up to switch so the 1st call switches the output ON and next call switches it OFF.

CREDIT ALERT & CHECKING

Only the follow networks are supported for SIM credit. 02 UK: To set up send: ;+CC1=*#100#;CREF.=1;
02 EIRE: To set up send: ;+CC1=*#10#;CREF.=1;
Vodafone UK: To set up send: ;+CC1=*#1345#;CREF#=2;

Set User to receive the alert: Send ;+LN6=1;TN1=07796176545; using your own User phone number.

Request the SIM credit: Send ;PCC1; OPERATION & TESTING

Follow these steps to test the system...

1.Switch on the power: The device will beep once every 10 seconds as it searches for the network. When it connects you will hear 3 quick beeps.

2.Program by SMS: Send minimum setting ;+ETN1=07796176545; (using your own phone number)

3. Reply confirmation: You should receive an SMS back to confirm the setting.

4. Press Call: The device will start calling and you will hear audible tones to start and then a ring tone; which can be muted ( ;+MUT=1;) 5. Open the door: Press 11 and you will hear relay 1 switch or press 21 & you will hear relay 2 swicth.

SWITCHING RELAY OUTPUTS

You have 4 ways to switch the outputs as follows...

During an intercom call (DTMF): Press 11 for output 1 'ON' & 10 for output 1 'OFF' (latching only)

page1image33464

QUICK-FIT BLACK RANGE

ANTI-VANDAL GSM DOOR ENTRY SYSTEM

SETUP MANUAL

page1image1896

QF BESPOKE

SET UP MANUAL

page2image1664

Version: v1.7
Valid from SW release "v_1_0_3.hex"

page2image2616 page2image2776

Page 2

QF BESPOKE SET UP MANUAL Contents

  1. 1  FOR YOUR SAFETY ................................................................................................... 6

  2. 2  INTRODUCTION ....................................................................................................... 7

  3. 3  FEATURES & APPLICATIONS........................................................................................ 8

  4. 4  ST ART UP .............................................................................................................. 9

  5. 5  LED STATUS DISPLAY .............................................................................................. 10

  6. 6  CLEAR ALL PROGRAMMED DA T A FROM SIM ................................................................... 11

  7. 7  CONNECTION DIAGRAM ........................................................................................... 12

  8. 8  PROGRAMMING QF BLACK GSM CONTROLLER ................................................................ 14

  9. 9  THE QF BLACK GSM CONTROLLER PARAMETERS............................................................. 15

    1. 9.1  ALARM INPUT SUPPORT ....................................................................................................15

    2. 9.2  RELAY OUTPUT MANAGEMENT .............................................................................................19

    3. 9.3  SECURITY LEVEL - AUTHORISED USERS....................................................................................20

    4. 9.4  CREDIT CHECK & SIM VALIDITY INFORMATION...........................................................................21

    5. 9.5  SET-UP PARAMETERS ........................................................................................................23

    6. 9.6  SMS MESSAGES EDITOR ......................................................................................................26

    7. 9.7  GSM INTERCOM...............................................................................................................27

    8. 9.8  CALLER ID RELAY CONTROL ................................................................................................30

    9. 9.9  EVENT LOGGING .............................................................................................................32

    10. 9.10  SPECIAL SMS COMMANDS ....................................................................................................33

  10. 10  PRINT-OUT OF THE PARAMETERS............................................................................... 35

    1. 10.1  RECEIVE ALL PARAMETERS (PALL) .........................................................................................35

    2. 10.2  CHECK SW VERSION (PSW).................................................................................................35

    3. 10.3  CHECK SIGNAL QUALITY (PSQ) ............................................................................................35

    4. 10.4  RECEIVE TELEPHONE NUMBERS (PTN).....................................................................................35

    5. 10.5  RECEIVE LINKS (PLN) ........................................................................................................35

    6. 10.6  RECEIVE INPUT PARAMETERS (PIN) ........................................................................................35

    7. 10.7  RECEIVE INPUT DELAY PARAMETERS (PID)................................................................................36

    1. 10.1  RECEIVE DIRECT OUTPUT PARAMETERS (POD) ...........................................................................36

    2. 10.2  RECEIVE DELAY BEFORE DIAL VALUE (PDD)...............................................................................36

    3. 10.3  RECEIVE ACCESS TELEPHONE NUMBERS (PSL)............................................................................36

    4. 10.4  RECEIVE OUTPUT STATUS PARAMETERS (POS) ...........................................................................36

    5. 10.5  RECEIVE ALL PROGRAMMED SMS MESSAGES (P#).........................................................................36

    6. 10.6  RECEIVE SET UP PARAMETERS VALUE (PPA) ..............................................................................36

    7. 10.7  RECEIVE CREDIT PARS PARAMETERS (PCREF) ...........................................................................37

    8. 10.8  RECEIVE ALL CLIP PARAMETERS (PCLP) ...................................................................................37

    9. 10.9  RECEIVE INTERCOM BUTTON 1 PARAMETERS (PDEA) ON BOARD MICRO-SWITCH BUTTON ..............37

    10. 10.10  RECEIVE INTERCOM BUTTON 2 PARAMETERS (PDEB) ON BOARD MICRO-SWITCH BUTTON...............37

    11. 10.11  RECEIVE INTERCOM BUTTON 3 PARAMETERS (PDEC) ON BOARD MICRO-SWITCH BUTTON ..............37

page3image19504 page3image19664 page3image19824 page3image19984

Page 3

QF BESPOKE SET UP MANUAL

page4image1352
  1. 10.12  RECEIVE INTERCOM BUTTON 4 PARAMETERS (PDED) ON BOARD MICRO-SWITCH BUTTON ..............38

  2. 10.13  RECEIVE INTERCOM BUTTON 5 PARAMETERS (PDEE) TERMINAL CONNECTION ON PCB (TERM. J4) ..............38

  3. 10.14  RECEIVE INTERCOM BUTTON 6 PARAMETERS (PDEF) TERMINAL CONNECTION ON PCB (TERM. J4)...............38

  4. 10.15  RECEIVE INTERCOM BUTTON 7 PARAMETERS (PDEG) TERMINAL CONNECTION ON PCB (TERM. J4) ..............38

  5. 10.16  RECEIVE INTERCOM BUTTON 8 PARAMETERS (PDEH) TERMINAL CONNECTION ON PCB (TERM. J4) ..............38

  6. 10.17  CREDIT CHECK FOR THE PAYG SIM CARD (NETWORK DEPENDENT) ....................................................38

  7. 10.18  RECEIVE CURRENT STATE OF THE OUTPUTS (PORC)....................................................................38

  8. 10.19  MANUAL GSM MODULE RESTART (MRES) (DOES NOT CLEAR PARAMETERS) ..........................................39

  9. 10.20  RECEIVE CURRENT ST A TUS OF INPUTS (INS)............................................................................. 39

  10. 10.21  RECEIVE SYSTEM EVENT LOG ...............................................................................................39

  1. 11  CHANGING PARAMETERS USING SMS COMMANDS ............................................................ 40

  2. 12  DEFAULT SETTINGS OF CONTROLLER.......................................................................... 41

  3. 13  P ARAMETER PRINT-OUT COMMANDS ........................................................................... 45

  4. 14  TECHNICAL SPECIFICA TION ...................................................................................... 46

  5. 15  SALES & SUPPORT CONT ACTS ................................................................................... 47

page4image10864 page4image11024

Page 4

QF BESPOKE SET UP MANUAL Figures

Figure 1, 1a, 2b: Connection diagrams .......................................................... 12 Figure 2: Input Connection diagram .............................................................. 15 Figure 3: Output Connection diagram ............................................................ 19

page5image2800 page5image2960 page5image3120 page5image3280

Page 5

QF BESPOKE SET UP MANUAL

page6image1360

1 FOR YOUR SAFETY

Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.

SWITCH ON SAFELY

Do not switch the unit on when use of wireless phone is prohibited or when it may cause interference or danger .

INTERFERENCE

All wireless phones and units may be susceptible to interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the unit off near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELING

Do not use the unit at a refueling point. Do not use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Do not use the unit where blasting is in progress.

USE SENSIBLY

Use only in the normal position as explained in the product documentation. Do not touch the antenna unnecessarily.

page6image11440 page6image11600 page6image11760

Page 6

QF BESPOKE SET UP MANUAL

page7image1360

2 INTRODUCTION

The QF BLACK GSM CONTROLLER is a simple GSM intercom communication system that is designed as a reliable, self contained solution for wireless door entry & communication applications. It is designed for unlimited range, wire free GSM intercom and Caller ID access control.

In addition the QF BLACK GSM CONTROLLER supports alarm detection, GSM network failure, unauthorised User, low credit limit and various other SMS notifications as detailed in this manual.

page7image5592 page7image5752 page7image5912

Page 7

QF BESPOKE

SET UP MANUAL

page8image1672

3 FEATURES AND APPLICATIONS

Features:

  • ⇒  Built-in tri-band GSM module

  • ⇒  Up to 4 way by direct connection to hardwired terminals

  • ⇒  2 alarm inputs (Press to exit & alarm sensor detection)

  • ⇒  Anti-tamper input

  • ⇒  2 relay outputs (250V 5A rated)

  • ⇒  Up to 100 Users for caller ID access control (unlimited in any caller mode)

  • ⇒  Programming by SMS, direct onto SIM using a mobile phone, USB SIM card reader, via

    PC using TeraTerm 4.7 (or HyperTerminal on Windows PC's) or via the dedicated PC application

    Applications:

    Complete door entry solution
    Wireless communication system
    Remote communication system (solar powered)
    Remote gate / door opener (Caller ID access control) Alarm notification by SMS

page8image9896 page8image10056 page8image10216

Page 8

QF BESPOKE SET UP MANUAL

page9image1392

4

START UP

  • ⇒  Insert SIM card to be used for QF BLACK GSM CONTROLLER in a mobile phone.

  • ⇒  Insert SIM card in QF BLACK GSM CONTROLLER device. The unit must be switched OFF when you insert the SIM!

  • ⇒  Connect inputs & outputs if required to QF BLACK GSM CONTROLLER. (optional)

  • ⇒  Connect the antenna to antenna connector and locate away from speaker area.

  • ⇒  Connect 12-24V AC/DC power to QF BLACK GSM CONTROLLER device

  • ⇒  Wait until LED1 (blue) starts flashing 3 - 5 times. (3 - 5 bars of signal) and the

    start up beep every 10 secs stops. When you hear 3 beeps the unit is on the

    network and ready to use.

  • ⇒  The QF BLACK GSM CONTROLLER unit is now ready to program.

page9image9520

IMPORT ANT

page9image11632 page9image11792

ERASE THE PIN CODE IF REQUESTED!

IMPORT ANT

page9image14976 page9image15136

Before sending any SMS commands to QF BLACK GSM CONTROLLER device, QF BLACK GSM CONTROLLER must not be beeping and to be reliable should have 3 - 5 flashes of signal strength!

page9image17616 page9image17776

Page 9

QF BESPOKE SET UP MANUAL

page10image1360

5 LED DISPLAY BLUE LED (LED1)

- Indicates the level of the GSM signal from 1 to 5 LED flashes (1 is weak signal, 5 is excellent signal). To be reliable, 3 - 5 is recommended however the device will operate as long as the blue LED is flashing.

-

Red LED (LED2)

- When LED 2 is ON the unit has a problem which is generally related to network signal, SIM card, antenna or something along these lines. Check all connections, SIM card is inserted correctly, activated (tested in a phone), antenna making connection, SIM credit etc. Try another network or using a higher gain antenna may be required in some circumstances. Please check these possible causes before calling for support.

-

Yellow LED (LED3)
- Short flashing indicates that the GSM module is ON, but it is not yet connected on the GSM

network. After connection, yellow led is flashing with short pulse ON and a long pulse OFF.

page10image10712 page10image10872 page10image11032

Page 10

QF BESPOKE SET UP MANUAL

page11image1376

6 CLEAR PREVIOUSLY EXISTING DATA FROM OLD SIM

This is highly recommended when a SIM card you are going to use for the QF BLACK GSM CONTROLLER is not new and it already has some data stored in the phone book memory.

By sending this SMS to the QF BLACK GSM CONTROLLER when the SIM card is in and on the network, all programmed parameters and numbers are cleared:
;SDCLR;

After sending SMS you should wait at least 2 minutes for the command to be executed! The device will automatically restart after the command has been committed.

page11image6888

NOTE

page11image8960 page11image9120

By sending this command to the QF BLACK GSM CONTROLLER all programmed data are erased from the SIM card!

page11image10976 page11image11136

Page 11

QF BESPOKE SET UP MANUAL

page12image1392

7 CONNECTION DIAGRAM

Before connection the QF BLACK GSM CONTROLLER please take note of the connection diagram.

CONNECTIONS:

Figure 1: QF BLACK GSM CONTROLLER Label Diagram TERMINAL LAYOUT & CONNECTIONS:

Figure 1a: QF BLACK GSM CONTROLLER Connection diagram (FRONT)

page12image4592 page12image4752 page12image4920 page12image5088 page12image5256 page12image5424 page12image5584

Page 12

QF BESPOKE SET UP MANUAL NOTE: Call button 1 - 4 are for use in a prefabricated enclosure and not for use as a bespoke device. For

bespoke applications, use button terminals 5 - 8.

Figure 1b: QF BLACK GSM CONTROLLER Connection diagram (REAR)

page13image3448 page13image3608 page13image3776 page13image3936

Page 13

QF BESPOKE SET UP MANUAL

page14image1360

8 PROGRAMMING QF BLACK GSM CONTROLLER

The QF BLACK GSM CONTROLLER device supports 4 different programming methods:

  • ⇒  To program QF BLACK GSM CONTROLLER parameters put the SIM card into a mobile phone. Add programming parameters in SIM Card "Phone Book" as names (parameter ie: ATN1) & number (setting ie: 07796167654)

  • ⇒  You can program QF BLACK GSM CONTROLLER remotely by SMS (text message). (typical for small installations with few Users or settings & also for post install updates)

  • ⇒  You can program QF BLACK GSM CONTROLLER with a USB SIM card reader in a PC USB port and enter the parameters as names (parameter ie: ATN1) & number (setting ie: 07796167654).

  • ⇒  You can use a PC to program QF BLACK GSM CONTROLLER by connecting the PC to the device mini USB port and using a terminal program (sending the SMS text message commands on screen) or using the dedicated PC program. (typical for installations with a lot of Users and settings - best done on the bench prior to going to site)

page14image10696 page14image10856 page14image11016

Page 14

QF BESPOKE SET UP MANUAL

page15image1416

9 THE QF BLACK GSM CONTROLLER PARAMETERS

To support maximum functionality of QF BLACK GSM CONTROLLER many highly configurable parameters are available. The parameters are divided into sections and are described in the following chapters.

9.1 ALARM INPUT SUPPORT

Alarm reporting is controlled by a series of different parameter groups. The first section is used to define the input configuration for the alarm to be triggered. The second section is used to configure the alarm reporting.

9.1.1 ALARM TRIGGERING

Parameters are used to control (filter) the triggering of the alarm inputs.

9.1.1.1 Input Configuration parameter

The IN parameter sets the way the inputs are triggered. Alarm activated and Alarm restored can be triggered in 2 different ways. The status of the input can either be normal closed (N.C) or normal open (N.O.) trigged with GND (default).

When you need notification the alarm has been restored you should select a setting from positon 4 or 5.

Note: INx=0 means IN1 or IN2 = 0

  • ⇒  INx=0 - Normal Open - triggered with negative voltage (GND) DEFAULT FOR IN1 & IN2

  • ⇒  INx=1 - Normal Close - breaking negative or positive voltage loop

  • ⇒  INx=2 - Not in use

  • ⇒  INx=3 - Not in use

page15image13536 page15image13696 page15image13856 page15image14016
  • ⇒  INx=4 means INx=0 + input restored SMS is sent

  • ⇒  INx=5 means INx=1 + input restored SMS is sent

  • ⇒  INx=6- Notinuse

    INPUT 1-4

INPUT 1-4

page15image16624 page15image17888

N.O. N.C. contact contact

G ND GND

Figure 2: Input 1 & 2 Connection diagram

page15image21872 page15image22032

Page 15

QF BESPOKE SET UP MANUAL 9.1.1.2 Input Delay parameter

The ID parameter determines the time period of the pulse length to trigger the alarm. The pulse time can be from 0,5 seconds to 9999 seconds. The default time is 0,5 seconds when the parameter value is 0.

9.1.1.3 Delay before Dial parameter

The DD parameter is used to define the delay between the time that alarm input is trigged and the time that alarm is reported.

page16image5296 page16image5456 page16image5616

9.1.1.4 Table of parameters

page16image6344
page16image7032

Name

page16image8688

Comment

IN1

Mode of operation for input 1

IN2

Mode of operation for input 2

ID1

Input time integration delay on input 1

ID2

Input time integration delay on input 2

DD1

Time delay for alarm reporting on input 1

DD2

Time delay for alarm reporting on input 2

page16image21672

Example:

Direct programming on the SIM card

Table 1: IN, ID and DD parameters

page16image25872

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

IN1

0

Alarm activated by connecting to GND

IN2

4

Alarm activated by connecting to GND + RST SMS

ID1

10

Input 1 has to be valid for 10 second to trigger the alarm

ID2

0

Input 2 has to be valid for 0,5 second to trigger the alarm

DD1

0

Reporting of the alarm on input 1 is delayed by 0s

DD2

15

page16image57488

Reporting of the alarm on input 1 is delayed by 15s

Table 2: IN, ID, DD parameters example

Remote programming by SMS (note: + means a reply is returned) ;+IN1=0;IN2=4;ID1=10;ID2=0;DD1=0;DD2=15;

9.1.2 REMOTE REPORTING ALARM EVENTS

Parameters used to define the way to report the alarm event. Page 16

page16image62056 page16image62216 page16image62376

QF BESPOKE SET UP MANUAL

page17image1520

NOTE

page17image3592 page17image3752

QF BLACK GSM CONTROLLER device sends SMS messages for reporting alarm events.

9.1.2.1 Telephone Number parameter

Telephone numbers (or authorized users) for remote alarm reporting are listed as TN parameters. Remote alarm reporting on QF BLACK GSM CONTROLLER is sent via SMS messages.

9.1.2.2 Link parameter

The Link parameter is used to link alarm event from inputs or preset events (LNx) to the telephone numbers from Telephone Number (TNx) list.

9.1.2.3 Line Open Time parameter

The LOT parameter is used to define the time control for voice calls. The start of voice connection starts the LOT timer. If the voice connection is still ON when the LOT timer expires QF BLACK GSM CONTROLLER disconnects voice connection regardless.

9.1.2.4 Table of parameters

page17image11808 page17image11968 page17image12128 page17image12288
page17image13072

Name

page17image14728

Comment

TN1

1st telephone number

TN2

2nd telephone number

TN3

3rd telephone number

TN4

4th telephone number

TN5

5th telephone number

LN1

Input & telephone No. linking for input 1 (to TN1 - TN5)

LN2

Input & telephone No. linking for input 2 (to TN1 - TN5)

LN5

Periodic test SMS. No. linking (TN1 - TN5)

LN6

Low credit alert No. linking (TN1 - TN5)

LN7

Non-authorised call or SMS (NAC - see note) No. linking (TN1 - TN5)

LN8

Log buffer status (TN1 - TN5)

LOT

Time out for GSM connection

page17image38800

Table 3: Remote alarm reporting parameters

Note (Non authorised call):

When a telephone number calling or messaging the QF BLACK GSM CONTROLLER is not on the TN or Caller ID access authorized lists, a non authorised event occurs (NAC). The telephone number responsible for this event can be sent to a TN user for notification.

page17image44552 page17image44712

Page 17

QF BESPOKE

SET UP MANUAL

page18image1760

Example:

Direct programming on the SIM card

page18image3864

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

TN1

07796176354

1st telephone number

LN1

13

Input 1 reports alarm to TN1 & TN3

LN2

1234

Input 2 reports alarm to TN1 & TN2 & TN3 & TN4

LN7

1

Non authorised event sent to TN1

LOT

60

Voice connection valid for max of 60s, after this time voice disconnects

Table 4: Remote alarm reporting example

Remote programming by SMS (note: + means a reply is returned) ;+TN1=07796176354;LN1=13;LN2=1234;LN7=1;LOT=60;

9.1.3 CONTROLLING OUTPUTS WITH DTMF

QF BLACK GSM CONTROLLER can control the outputs with the use of DTMF.
To control the outputs the user must press the combination of 2 digits as shown below.

page18image35648

NOTE

page18image37720 page18image37880

QF BLACK GSM CONTROLLER must be in voice connection to support DTMF output control!

Example:

DTMF combination

Description

00

Deactivate ALL outputs

01

Activate ALL outputs

11

Activate output 1 (pulse most common)

10

Deactivate output 1 (if in latch mode)

21

Activate output 2 (pulse most common)

20

page18image58648

Deactivate output 2 (if in latch mode)

Table 5: DTMF control example

page18image60688 page18image60848

Page 18

QF BESPOKE SET UP MANUAL 9.2 OUTPUT MANAGEMENT

QF BLACK GSM CONTROLLER supports the possibility to report alarms from inputs and any other events locally via 2 outputs. The behavior is defined using next parameters

9.2.1 OS parameter

The QF BLACK GSM CONTROLLER device has 2 relay outputs. Outputs can be configured to pulse, latch or timed pulse:

page19image4568 page19image4728 page19image4888
  • ⇒  OSx=0

  • ⇒  OSx=1

  • ⇒  OSx=XXX

- Disabled
- Bi-stable toggle mode (latch)
- Mono-stable (pulse)
(duration in seconds)

Typical connection for the output:

OUTPUT 1-4

LED

R1K

+12V DC

Figure 1: Output 1 & 2 Connection diagram 9.2.2 Direct Output parameter (press to exit)

OUTPUT 1-4

RELAY 12V DC

page19image10728 page19image11152 page19image11576 page19image12336 page19image12760 page19image12920 page19image13080 page19image13240 page19image13664

The OD parameter is used to link the alarm event directly to output. Activity on an alarm input can automatically switch an output. A typical use for this is 'Press to Exit'. Set ;+OD1=1; and input 1 will trigger output 1.

9.2.3 Output parameters

Parameters are used to invert the polarity of the outputs.

  • ⇒  0 - normal (N/O) DEFAULT

  • ⇒  1 - inverted (N/C)

+12V DC

page19image18656 page19image18816 page19image18976 page19image19136

Page 19

QF BESPOKE

SET UP MANUAL

page20image1832

9.2.4 Table of parameters

page20image2560
page20image3264

Name

page20image4920

Comment

OS1

Mode of operation for output 1

OS2

Mode of operation for output 2

OD1

Input 1 direct link to outputs

OD2

Input 2 direct link to outputs

OD5

Non authorised User activates a direct link to output 1 or 2

OP1

Invert switching configuration for output 1

OP2

Invert switching configuration for output 2

page20image19728

Example:

Table 6: Output management parameters

Direct programming on the SIM card

page20image23824

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

OS1

1

Bistable toggle mode

OS2

3

Monostable pulse mode (3sec pulse)

OD1

1

Input 1 activates output 1

OD2

2

Input 2 activates output 2

OP1

1

page20image50376

Output 1 inverted

Table 7: Output management parameters example

Remote programming by SMS (note: + means a reply is returned) ;+OS1=1;OS2=3;OD1=1;OD4=2;OP1=1;

9.3 SECURITY LEVEL - SL

SL parameter from 0 to 5 defines which telephone numbers stored in the phone book from TN1 - TN5 can enter into programming and remote control of the QF BLACK GSM CONTROLLER device.

page20image55384

NOTE

When the SL level is 0, an access to the QF BLACK GSM CONTROLLER is possible from any phone!

IMPORT ANT

Before any SL number is programmed the QF BLACK GSM CONTROLLER can accept ALL CALLS. Remote SMS programming and remote controlling is possible from any phone!

page20image64360 page20image64520

Page 20

QF BESPOKE

SET UP MANUAL

page21image1784
page21image2472

Name / value

page21image4208

Comment

SL = 0

All calls and SMS are accepted

SL = 1

Only number stored under parameter TN1 has access to unit

SL = 2

Numbers stored under parameters TN1 to TN2 have access to unit

SL = 3

Numbers stored under parameters TN1 to TN3 have access to unit

SL = 4

Numbers stored under parameters TN1 to TN4 have access to unit

SL = 5

Numbers stored under parameters TN1 to TN5 have access to unit

page21image18912

Example:

Table 8: SL parameter

page21image22184

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

SL

3

Numbers stored under parameters TN1 to TN3 have access to unit

page21image36032

;+SL=3;
9.4 PREPAID SIM CREDIT ALERTS

QF BLACK GSM CONTROLLER can be used with prepaid SIM cards and its limitations. To be able to overcome this limitation of the prepaid SIM cards, QF BLACK GSM CONTROLLER offers the possibility of automatic checking mechanism for credit.

9.4.1.1 SIM Card Credit parameters

Number used to check low credit value. They are provided from the GSM providers.

CC1 - This setting is only supported on a few networks (Vodafone & 02 UK and 02 Ireland)

Direct programming on the SIM card

Table 9: SL example
Remote programming by SMS (note: + means a reply is returned)

page21image43176

NOTE

QF BLACK GSM CONTROLLER automatically sends warning SMS when the credit reaches low level defined by LCV parameter or SIM card validity is near to expiration.

page21image47648 page21image47808 page21image47968

Page 21

QF BESPOKE SET UP MANUAL 9.4.1.2 CREF, CTIM, CVODA parameters

Parameters are used to find the credit value of the prepaid SIM card. Strings under these parameters are used to pars the replay message from the GSM provider.

CREF - Currency reference linked to the CC1 parameter. Use the details for the supported networks as set out in the examples in this manual only

9.4.1.3 Table of parameters

page22image4968 page22image5128 page22image5288
page22image5944

Name

page22image7600

Comment

LCV

Low credit value, bottom limit for low credit event.

CC1

Credit number for credit check universally used

LN6

Link to User for low credit alert

CREF

String for currency reference (set as shown)

page22image16936

Example:

Table 10: Prepaid card validity parameters

Direct programming on the SIM card

page22image20776

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

LCV

4

Low credit message will be send below 4

CC1

*#1345#

Vodafone UK (02 UK is *#100# & 02 Ireland is *#100# )

LN6

1

SIM credit alert to User 1 (TN1)

CREF#

2

Vodafone UK setting

CREF.

1

02 UK setting

CREF.

1

page22image52536

02 Ireland setting

Table 11: Credit example

Remote programming by SMS (note: + means a reply is returned) ;+LCV=4;CC1=*1345#;LN6=1;CREF#=2; (OR ;CREF.=1; FOR 02 UK)

page22image55256 page22image55416

Page 22

QF BESPOKE SET UP MANUAL

page23image1400

9.5 SET-UP PARAMETERS

Different parameters are used to support versatile functionality of the QF BLACK GSM CONTROLLER.

9.5.1 HTN parameter

Hidden telephone number is a parameter used in order to conceal the telephone number of the SIM card in the QF BLACK GSM CONTROLLER device. The default value is set to "1" which means that the number is shown. Eg: ;+HTN=0; (hide number)

9.5.2 ESC parameter

Parameter is used to define the input used to cancel the current call from the QF BLACK GSM CONTROLLER device. A separate button on teh door entry panel labelled 'cancel' can be connected to GND & IN1 and ;+ESC=1; to enable the function.

9.5.3 UDC parameter

Parameter is used to synchronise the QF BLACK GSM CONTROLLER clock to GSM network clock. You must enter the number of the SIM card in the QF BLACK GSM CONTROLLER device. When power is lost and restored the device sends itself an SMS to update itthe onboard clock. Eg: ;+UDC=07796434543;

9.5.4 RAN parameter

Parameter is used to provide support for auto-answer DTMF options for the QF BLACK GSM CONTROLLER device. The number defines the number of rings needed for QF BLACK GSM CONTROLLER device to answer the incoming call. The incoming number must be on the TN list (authorised users) for the device to answer. When the device answers it will beep in the earpiece and the User is connected. DTMF control of can then be used as outlined in this manual. Eg: ;+RAN=1; (answers quickly) NOTE: Do not call the device from a number on the CLIP list (Caller ID access) because the device may answer before the actual required function of switching an output has been aactivated.

9.5.5 TST parameter

A test SMS can be sent periodically at intervals between 1 hour to 240 hours.

Example:
If send test SMS TST value is set to 12 (;+TST=12;) , the TN number/s linked to "LN5" receive a test message every 12 hours.

page23image19120 page23image19280 page23image19440 page23image19600 page23image19760 page23image19920 page23image20080 page23image20240

Page 23

QF BESPOKE

SET UP MANUAL

page24image1800

9.5.6 MIC parameter

MIC parameter enables you to change the sound level on the microphone. Eg: ;+MIC=4;

9.5.7 SPK parameter

SPK parameter enables you to change the speaker sound level. Eg: ;+SPK=12;

9.5.8 MUT parameter

MUT parameter enables you mute the speaker sound while the actual ringing occurs. It does not mute the initial bell press beep or connection beeps. This is useful if the User is travelling and wants to mute the international ringing tone. Eg: ;+MUT=1;

9.5.9 ARST parameter

ARST parameter defines periodic of auto restart time (in hours) of the device. It does not clear any parameters. It's simply an automatic module restart. Eg: :+ARST=48;

9.5.10 ADFparameter

Parameter is used to make an automatic call after a preset amount of days. It is useful if the system will not be used for some time and a PAYG SIM card is used. In this case the device can call after say 100 days to prevent the network cutting the SIM card off through non use. The threshold period differs between networks. Contact your SIM Provider. Eg: :+ADF=100;

9.5.11 BUZparameter

Parameter is used to control buzzer when output operates and some other functions that make the buzzer sound. If the buzzer sounds and you don't want it to, activate this feature to disable it. Eg: ;+BUZ=1;

9.5.12 Table of parameters

page24image14528 page24image14688 page24image14848 page24image15008 page24image15168 page24image15328 page24image15488
page24image16208

Name

page24image17864

Comment

UDC

Update clock - must = number of SIM in device

ESC

Input used as cancel button = 1 means IN1 active cancels call in progress. Useful for a cancel button on door enrty panel in case incorrect button is pressed

RAN

Rings to answer. Device answers call and gives User DTMF control of system

HTN

Hide device telephone number

TST

SMS test send

MIC

Microphone volume control

SPK

Speaker volume control

ARST

Time out for automatic system restart

page24image36992 page24image37152

Page 24

QF BESPOKE

SET UP MANUAL

page25image1712

ADF

Auto dial functionality ( Call TN1) Keep SIM active. Set in days to make an automatic call after set number of days

BUZ

Buzzer control - Beeps when output activated.

page25image6552

Example:

Table 12: Set-up parameters Direct programming on the SIM card

page25image9384

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

HTN

1

Telephone number of device hidden (=0 means number is shown)

MIC

4

Audio level for person on telephone end

SPK

12

Audio level for person at door panel end

TST

168

168 hours periodic test SMS

BUZ

0

Mute buzzer

ESC

2

page25image41768

Input 2 is used as cancel button

Table 13: Set-up parameters example.

Remote programming by SMS (note: + means a reply is returned) ;+HTN=1;LNG=1;MIC=4;SPK=12;TST=24; BUZ=0;ESC=2;

page25image44688 page25image44848

Page 25

QF BESPOKE SET UP MANUAL

page26image1512

9.6 SMS MESSAGES EDITOR

You can edit the label for each alarm input. Each message is built from 3 parts and user can write the first (User Location ie: my gate) and the second (name of event or label of input ie: intruder or door sensor) part of the message. Unit adds the third part (alarm event description) automatically ie: (alarm activity in progress or alarm input restored). The message is stored in the SIM phone book so you should add any number for correct operation.

page26image6152

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

page26image19096

#

0

U

S

E

R

L

O

C

A

T

I

O

N

#

1

I

N

P

U

T

1

#

2

I

N

P

U

T

2

page26image50224

NOTE

page26image53360 page26image53520

Message should not be longer than 14 characters! Space is also counted as one character!

9.6.1 Table of parameters

page26image55784
page26image56424

Name

page26image58080

Comment

#0

Device location, same for all alarm messages

#1

Input 1, second part of message

#2

Input 2, second part of message

page26image65392

Example:

Table 14: Message parameters

Direct programming on the SIM card

Table 15: Message parameters example
Remote programming by SMS (note: + means a reply is returned)

;+#0USERS_HOME=1;#1MAIN_GA TE=1;#2PED_GA TE=1;

page26image70024

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

#0USERS_HOME

1

Location definition

#1MAIN_GA TE #2PED_GA TE

page26image85344

1 1

Alarm input 1 is a door contact on main gate Alarm input 2 is a sensor

page26image89256
page26image89896 page26image90056

Page 26

QF BESPOKE SET UP MANUAL 9.7 INTERCOM

For each button the QF BLACK GSM CONTROLLER incorporates a group of parameters to set up the call button. There 8 groups of parameters for the 8 possible call buttons however only 5 - 8 relate to the QF BLACK GSM CONTROLLER as 1 - 4 are on board micro-switch call buttons that are only used on a different door entry panel version.

9.7.1 ATN1 to ATN5 (xTN1 - xTN5) parameters

Parameters are phone numbers for the intercom call buttons.

The prefixed letter 'A' 'B' 'C' 'D' 'E' 'F' 'G' 'H' relate to call buttons 1 - 8 therefore for the purpose of the QF BLACK GSM CONTROLLER manual only 'E' 'F' 'G' 'H' are relevant.

9.7.2 RTN parameter

Parameter defines the ring time between numbers. Only one time can be set per group and will be the delay between all numbers on the xTN1 - xTN5 list. The RTN timer is started when the call button is pressed so some trial and error may be required if trying to set a timer to avoid voicemail. If the RTNx timer expires before the GSM voice connection is established then the device calls the next number in xTN1 - xTN5 call list.

The suffixed letter 'A' 'B' 'C' 'D' 'E' 'F' 'G' 'H' relate to groups 1 - 8 therefore for the purpose of the QF BLACK GSM CONTROLLER manual only 'E' 'F' 'G' 'H' are relevant.

9.7.3 DTMF auto dial functionality

This function is used to provide support for QF BLACK GSM CONTROLLER device to be able select extended numbers via DTMF command. It is used to make the GSM intercom automatically interface with switchboards that require a code to be pressed to progress through the system. Ie: press 1 for reception. Although it is generally recommended to make the calls direct to a number rather than a switchboard the QF BLACK GSM CONTROLLER can handle the call transfer by entering the required digital with a suitable time delay as required.

9.7.3.1 SDNx parameter

Parameter is used to set the DTMF number in auto self select function. Which number is to be pressed. Ie: ;+SDNF=1; group 'F' used as an example

The suffixed letter 'A' 'B' 'C' 'D' 'E' 'F' 'G' 'H' relate to groups 1 - 8 therefore for the purpose of the QF BLACK GSM CONTROLLER manual only 'E' 'F' 'G' 'H' are relevant.

9.7.3.2 SDDx parameter

Parameter is used to set the delay ( in seconds ) for sending the chosen DTMF number in auto self select function as above (SDNx). Ie: ;+SDDF=2; group 'F' used as an example

The suffixed letter 'A' 'B' 'C' 'D' 'E' 'F' 'G' 'H' relate to groups 1 - 8 therefore for the purpose of the QF BLACK GSM CONTROLLER manual only 'E' 'F' 'G' 'H' are relevant.

page27image25368 page27image25528 page27image25688 page27image25848 page27image26008 page27image26168 page27image26328 page27image26488 page27image26648

Page 27

QF BESPOKE SET UP MANUAL 9.7.4 Call Button Time Zone & After Hours Disable

Time zone support is to enable the call button during certain hours and can be used to conversely to disable the call button outside of the set hours by leaving the 5th call number off the list ie: only using 4 call numbers maximum. When both time limits are set (in 24hr format :00 not necessary just 0 - 24) - (ie: ;+TZSF=6;TZEF=18; is 6:00 - 18:00) the time zone functionality for that group (F in this example) is ON. When the current time is in the limits of the time zone parameters the button event calls the number from xTN1 to xTN4, outside of these set hours the device calls directly to xTN5. For this reason if you leave xTN5 blank, outside of the set hours the device will not make a call effectively disabling the call button outside of the set hour range.

9.7.4.1 Time Zone Start TZSx parameter

Parameter is used to configure the start time for the time zone functionality - 24h time format. Ie: ;+TZSF=6; (6am or 6:00) group 'F' used as an example

The suffixed letter 'A' 'B' 'C' 'D' 'E' 'F' 'G' 'H' relate to groups 1 - 8 therefore for the purpose of the QF BLACK GSM CONTROLLER manual only 'E' 'F' 'G' 'H' are relevant.

9.7.4.2 Time Zone End TZEx parameter

Parameter is used to configure the end time for the time zone functionality - 24h time format. Ie: ;+TZEF=18; (6pm or 18:00) group 'F' used as an example

The suffixed letter 'A' 'B' 'C' 'D' 'E' 'F' 'G' 'H' relate to groups 1 - 8 therefore for the purpose of the QF BLACK GSM CONTROLLER manual only 'E' 'F' 'G' 'H' are relevant.

9.7.5 Table of parameters (grey text not relevant to QF BLACK GSM Controller)

page28image16768 page28image16928 page28image17088 page28image17248 page28image17408
page28image19016

Name

page28image20840

Comment

A TN1

Button 1, Telephone number 1.

A TN2

Button 1, Telephone number 2.

A TN3

Button 1, Telephone number 3.

A TN4

Button 1, Telephone number 4.

A TN5

Button 1, Telephone number 5.

RTNA

Button 1, time out control for voice connection.

SDNA

Button 1, DTMF number to send.

SDDA

Button 1, delay for DTMF number to send.

TZSA

Button 1, time zone start period.

TZEA

Button 1, time zone end period.

BTN1

Button 2, Telephone number 1.

BTN2

Button 2, Telephone number 2.

BTN3

Button 2, Telephone number 3.

BTN4

Button 2, Telephone number 4.

BTN5

Button 2, Telephone number 5.

RTNB

Button 2, time out control for voice connection.

SDNB

Button 2, DTMF number to send.

SDDB

Button 2, delay for DTMF number to send.

TZSB

Button 2, time zone start period.

TZEB

Button 2, time zone end period.

CTN1

Button 3, Telephone number 1.

page28image87024 page28image87184

Page 28

QF BESPOKE

SET UP MANUAL

page29image2552

CTN2

CTN3

RTNC

Button 3, Telephone number 2.

Button 3, Telephone number 3.

CTN4

Button 3, Telephone number 4.

CTN5

Button 3, Telephone number 5.

Button 3, time out control for voice connection.

SDNC

TZSC

Button 3, DTMF number to send.

SDDC

Button 3, delay for DTMF number to send.

Button 3, time zone start period.

TZEC

Button 3, time zone end period.

page29image16448 page29image16616 page29image16784 page29image16952 page29image17120 page29image17288 page29image17456 page29image17624 page29image17792 page29image17960

DTN1

page29image18576

DTN2

Button 4, Telephone number 1.

Button 4, Telephone number 2.

DTN3

DTN5

Button 4, Telephone number 3.

DTN4

Button 4, Telephone number 4.

Button 4, Telephone number 5.

RTND

SDDD

Button 4, time out control for voice connection.

SDND

Button 4, DTMF number to send.

Button 4, delay for DTMF number to send.

TZSD

Button 4, time zone start period.

TZED

Button 4, time zone end period.

page29image33080 page29image42576 page29image52072 page29image61568 page29image61728 page29image61888 page29image62848 page29image63016 page29image63184 page29image63352 page29image63520 page29image63688 page29image63856 page29image64024 page29image64184 page29image64344 page29image64504 page29image64664 page29image64824
  1. ETN1  Button 5, T elephone number 1.

  2. ETN2  Button 5, T elephone number 2.

  3. ETN3  Button 5, Telephone number 3.

  4. ETN4  Button 5, T elephone number 4.

  5. ETN5  Button 5, T elephone number 5.

RTNE Button 5, time out control for voice connection. SDNE Button 5, DTMF number to send.

SDDE Button 5, delay for DTMF number to send. TZSE Button 5, time zone start period.
TZEE Button 5, time zone end period.

  1. FTN1   page29image74328 page29image74536 page29image74744 page29image74952 page29image75160 page29image75368 page29image75576 page29image75784Button 6, T elephone number 1.

  2. FTN2  Button 6, T elephone number 2.

  3. FTN3  Button 6, T elephone number 3.

  4. FTN4  Button 6, T elephone number 4.

  5. FTN5  Button 6, T elephone number 5.

RTNF Button 6, time out control for voice connection SDNF Button 6, DTMF number to send.

SDDF Button 6, delay for DTMF number to send. TZSF Button 6, time zone start period.
TZEF Button 6, time zone end period.

  1. GTN1   page29image80776 page29image80984 page29image81192 page29image81400 page29image81608 page29image81816 page29image82024 page29image82232Button 7, T elephone number 1.

  2. GTN2  Button 7, T elephone number 2.

  3. GTN3  Button 7, T elephone number 3.

  4. GTN4  Button 7, T elephone number 4.

  5. GTN5  Button 7, T elephone number 5.

RTNG Button 7, time out control for voice connection SDNG Button 7, DTMF number to send.

SDDG Button 7, delay for DTMF number to send. TZSG Button 7, time zone start period.
TZEG Button 7, time zone end period.

  1. HTN1   page29image87224 page29image87432 page29image87640 page29image87848 page29image88056 page29image88264 page29image88472 page29image88680Button 8, T elephone number 1.

  2. HTN2  Button 8, T elephone number 2.

  3. HTN3  Button 8, Telephone number 3.

  4. HTN4  Button 8, T elephone number 4.

  5. HTN5  Button 8, T elephone number 5.

RTNH Button 8, time out control for voice connection SDNH Button 8, DTMF number to send.

page29image91896 page29image92056 page29image92216 page29image92376 page29image92536 page29image92696 page29image92856 page29image93016 page29image93176 page29image93336 page29image93504 page29image93672 page29image93840 page29image94008 page29image94176 page29image94344 page29image94512 page29image94680 page29image94848 page29image95016 page29image95184 page29image95344 page29image95504 page29image95664 page29image95824 page29image95984 page29image96144 page29image96304 page29image96464 page29image96624 page29image96784 page29image96944 page29image97112 page29image97280 page29image97448 page29image97616 page29image97784 page29image97952 page29image98120 page29image98288 page29image98456 page29image98624 page29image98784 page29image98944 page29image99104 page29image99264 page29image99424 page29image99584 page29image99744 page29image99904 page29image100064 page29image100224 page29image100384 page29image100552 page29image100720 page29image100888 page29image101056 page29image101224 page29image101392 page29image101560 page29image101728 page29image101896 page29image102064 page29image102224 page29image102384 page29image102544 page29image102704 page29image102864 page29image103024 page29image103184 page29image103344 page29image103504 page29image103664 page29image103824

Page 29

QF BESPOKE

SET UP MANUAL

page30image1760

SDDH

Button 8, delay for DTMF number to send.

TZSH

Button 8, time zone start period.

TZEH

Button 8, time zone end period.

page30image7736

Example:

Direct programming on the SIM card

Table 16: Intercom parameters

page30image11192

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

ATN1

07796176354

Button 1, Telephone number 1.

ATN2

+447796176355 

Button 1, Telephone number 2.

RTNA

30

Button 1, time out control for voice connection.

CTN1

07796176356

Button 3, Telephone number 1.

CNT2

07796176357

Button 3, Telephone number 1.

RTNC

40

page30image42360

Button 3, time out control for voice connection.

Table 17: Intercom parameters example

Remote programming by SMS (note: + means a reply is returned)
;+A TN1=07796176354;A TN2=+447796176355;RTNA=30;CTN1=07796176356;C

TN2=07796176357;RTNC=40;

9.8 CLIP CALLER ID ACCESS CONTROL (100 USER)

CLIP is used to provide "free of charge" control of a selected (1) output for up to 100 authorised users. It can also be opened up so any number calling will switch the output making the number of users unlimited and within only a group that know which number to call.

9.8.1 CLPEN parameter

Parameter used to enable / disable / lock down to authorised users for CLIP access. Ie: ;+CLPEN=2; (open access - any caller mode)

9.8.2 CLPOU parameter

Parameter used to choose which output will be controlled by the CLIP feature. Ie: ;+CLPOU=1; (output 1)

page30image51720 page30image51880 page30image52040 page30image52200 page30image52360

Page 30

QF BESPOKE SET UP MANUAL 9.8.3 CLPI parameter

This parameter, if set, dictates which input 1 or 2 must be active in order for the CLIP feature to work. This is particularly useful in situation where the Owner of the system doesn't want Users to be able to switch the gate or door from afar. It would be used like an arming loop is used at a ticket machine. The ticket will not issue unless a car is on the arming loop. Similarly, the CLIP feature will not work unless the sensor put in place has been firstly activated before the User calls. Ie: ;+CLPI=1; (input 1 must be active for CLIP to function)

9.8.4 CLP1 ... CLP100 parameter

Set of telephone number, which can control the output. The number not on CLP list is not able to control the output using clip functionality. Ie: ;+CLP1=07796176354;CLP2=07796176355;CLP100=07796176356; (add users 1, 2 & 100) ;+CLP1=;CLP2=;CLP100=; (delete users 1,2 & 100)

9.8.5 Table of parameters

page31image9456 page31image9616 page31image9776 page31image9936
page31image10656

Name

page31image12312

Comment

CLPEN

Enable CLIP functionality

CLPOU

Control output when CLIP call received

CLPI

CLIP input activation requirement

CLP1

CLIP number 1

.

.

.

.

.

.

CLP100

CLIP number 100

page31image27664

Example:

Table 18: CLIP parameters Direct programming on the SIM card

page31image31616

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

CLPEN

1

Enable CLIP functionality

CLPOU

2

CLIP control output 2

CLPI

0

No input activation condition

CLP1

07796176354

User number 1

CLP2

07796176355

User number 2

CLP100

07796176356

page31image63400

User number 100

Table 19: CLIP parameters example

Remote programming by SMS(note: + means a reply is returned) ;+CLPEN=1;CLPOU=2;CLPI=0;CLP1=07796176354;CLP2=07796176355;CLP100=

07796176356;

page31image66336 page31image66496

Page 31

QF BESPOKE SET UP MANUAL 9.9 EVENT LOGGING

The QF BLACK GSM CONTROLLER logs certain events on the alarm input side of the device. Log events consist of event, time and telephone number or input number.

9.9.1 Log Number LOGN parameter

Parameter is used for defining the number of events printed out on PLOG request. Ie: ;PLOG; returns events...... ;+LOGN=5; defines how many individual log events are returned as 1 SMS per event

9.9.2 Log Interface LOGI parameter

Parameter is used to define the media used for logging of events on QF BLACK GSM CONTROLLER. User can select between nonvolatile memory on QF BLACK GSM CONTROLLER or select USB to transfer events directly via USB to PC.

9.9.3 Auot Log Clear ALC parameter

Parameter is used to control behavior when log on QF BLACK GSM CONTROLLER is full. User can select between auto log clear or manual clear of log.

page32image9384 page32image9544 page32image9704 page32image9864 page32image10024

9.9.4 Table of parameters

Example:

Table 20: LOG parameters.

page32image11480
page32image12120

Name

page32image13776

Comment

LOGN

Number of log events for printing out

LOGI

Log interface

ALC

Automatic log clear

page32image20808

Direct programming on the SIM card

Table 21: LOG parameters example
Remote programming by SMS (note: + means a reply is returned)

;+LOGN=5;LOGI=0;ALC=1;
Page 32

page32image24552

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

SIM CARD PHONE BOOK

Name

Number

Description

LOGN

5

5 log events will be printed out on PLOG command

LOGI

0

Nonvolatile memory on QF BLACK GSM CONTROLLER

ALC

1

Log is auto cleared when full

page32image46416 page32image46576

QF BESPOKE SET UP MANUAL 9.10 SPECIAL SMS COMMANDS

These commands can only be issued only over SMS message, and are used to control some special functions of QF BLACK GSM CONTROLLER device.

9.10.1 OutputRemoteControlORCcommand

Command is used to control the 2 outputs via SMS message. Output 1 ON ;+ORC1=1;

Output 1 OFF (only if set to latching) ;+ORC1=0; Output 2 ON ;+ORC2=1;

Output 2 OFF (only if set to latching) ;+ORC2=0; 9.10.2 SIM Data Clear SDCLR command

To clear all data on SIM card SDCLR command is used. Use carefully. All factory settings restored.

9.10.3 LogClearLCLRcommand

Command clears log on QF BLACK GSM CONTROLLER device.

9.10.4 CLIPClearCLPCLRcommand

Command is used to delete all CLP numbers.

9.10.5 Module Reset MRES command

Command is used to manually restart GSM module on QF BLACK GSM CONTROLLER device. Does not clear data. Reboots the GSM only. Not the system firmware. Use SSRES to reboot device completely.

9.10.6 SoftwareResetSSREScommand

Command is used to manually restart QF BLACK GSM CONTROLLER device. Does not clear data. This resent command is like a power cycle.

page33image12176 page33image12336 page33image12496 page33image12656 page33image12816 page33image12976 page33image13136 page33image13296 page33image13456 page33image13616

Page 33

QF BESPOKE

SET UP MANUAL

page34image1776

9.10.7 Table of parameters

page34image2504
page34image3192

Name

page34image4848

Comment

ORC1

Control of output 1

ORC2

Control of output 2

SDCLR

Delete all SIM content

LCRL

Delete log on QF BLACK GSM CONTROLLER device

MRES

Manual reset of GSM module

SSRES

Manual reset of QF BLACK GSM CONTROLLER device

page34image17472

Example:

Remote programming by SMS

Table 22: SMS commands

SMS commad

Description

;ORC1=1;

Activate output 1

;ORC2=0;

Deactivate output 2

;SDCLR;

Clear all data on SIM

;LCLR;

Delete log on QF BLACK GSM CONTROLLER device

;MRES;

Manual reset of GSM module

;SSRES;

page34image40104

Manual reset of QF BLACK GSM CONTROLLER device

Table 23: SMS commands example

page34image42024 page34image42184

Page 34

QF BESPOKE SET UP MANUAL

page35image1408

10 PRINT-OUT OF THE PARAMETERS

The user can check the settings of ALL parameters on the QF BLACK GSM CONTROLLER.

10.1 RECEIVE ALL PARAMETERS (PALL)

By sending this command to QF BLACK GSM CONTROLLER you receive many SMS messages with all parameters that are currently programmed in the unit (up 25 message may be received. Using a PC with TerTerm 4.7 or HyperTerminal is recommended for this feature:
;PALL;

10.2 CHECK SW REVISION (PSW)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS messages with current firmware running on the device:
;PSW;

10.3 CHECK SIGNAL QUALITY (PSQ)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS messages with signal quality QF BLACK GSM CONTROLLER device is connected to network (1 low to 5 high):
;PSQ;

10.4 RECEIVE TELEPHONE NUMBERS (PTN)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed telephone numbers (TN1 - TN5):
;PTN;

10.5 RECEIVE LINKS (PLN)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed links (LN1 -LN8):
;PLN;

10.6 RECEIVE INPUT PARAMETERS (PIN)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed Input parameters (IN1 - IN4):
;PIN;

page35image14616 page35image14776 page35image14936 page35image15096 page35image15256 page35image15416 page35image15576 page35image15736 page35image15896

Page 35

QF BESPOKE SET UP MANUAL 10.7 RECEIVE INPUT FILTER VALUE (PID)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed Input filters (ID1 - ID4):
;PID;

10.1 RECEIVE INPUT FILTER VALUE (POD)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed direct output links (OD1 - OD5):
;POD;

10.2 RECEIVE DELAY BEFORE DIAL VALUE (PDD)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed Input filters (DD1 - DD4):
;PDD;

10.3 RECEIVE ACCESS TELEPHONE NUMBERS (PSL)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with programmed SL level:
;PSL;

10.4 RECEIVE OUTPUT PARAMETERS (POS)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed Outputs parameters (OS1 - OS2):
;POS;

10.5 RECEIVE ALL PROGRAMMED SMS MESSAGES (P#)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed alarm SMS messages (#0 - #4):
;P#;

10.6 RECEIVE SET UP PARAMETERS VALUE (PPA)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed Setup parameters (MIC, SPK, etc...):
;PPA;

page36image13848 page36image14008 page36image14168 page36image14328 page36image14488 page36image14648 page36image14808 page36image14968 page36image15128 page36image15288

Page 36

QF BESPOKE SET UP MANUAL 10.7 RECEIVE CREDIT PARS PARAMETERS (PCREF)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed credit check parameters (CREF, CC1 etc...):
;PCREF;

10.8 RECEIVE ALL CLIP PARAMETERS (PCLP)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed CLIP functionality related parameters ( CLPEN, CLPOU, CLPI, CLPx):
;PCLP;

page37image5096 page37image5256 page37image5416

NOTE

page37image7488 page37image7648

User can use ;PCLP=x,y; to limit the number of CLIP numbers to be printed.

x = start number y = end number

Example
;PCLP=1, 30; Prints first 30 CLIP numbers

10.9 RECEIVE INTERCOM BUTTON 1 PARAMATERS (PDEA)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 1 group parameters ( ATN1, ATN2, ATN3, ATN4, ATN5, RTNA, SDNA, SDDA, TZSA, TZEA ):
;PDEA;

10.10 RECEIVE INTERCOM BUTTON 2 PARAMATERS (PDEB)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 2 group parameters ( BTN1, BTN2, BTN3, BTN4, BTN5, RTNB, SDNB, SDDB, TZSB, TZEB ):
;PDEB;

10.11 RECEIVE INTERCOM BUTTON 3 PARAMATERS (PDEC)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 3 group parameters ( CTN1, CTN2, CTN3, CTN4, CTN5, RTNC, SDNC, SDDC, TZSC, TZEC ):
;PDEC;

page37image17824 page37image17984 page37image18144 page37image18304 page37image18464

Page 37

QF BESPOKE SET UP MANUAL 10.12 RECEIVE INTERCOM BUTTON 4 PARAMATERS (PDED)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 4 group parameters ( DTN1, DTN2, DTN3, DTN4, DTN5, RTND, SDND, SDDD, TZSD, TZED ):
;PDED;

10.13 RECEIVE INTERCOM BUTTON 5 PARAMATERS (PDEE)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 5 group parameters ( ETN1, ETN2, ETN3, ETN4, ETN5, RTNE, SDNE, SDDE, TZSE, TZEE ):
;PDEE;

10.14 RECEIVE INTERCOM BUTTON 6 PARAMATERS (PDEF)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 6 group parameters ( FTN1, FTN2, FTN3, FTN4, FTN5, RTNF, SDNF, SDDF, TZSF, TZEF ):
;PDEF;

10.15 RECEIVE INTERCOM BUTTON 7 PARAMATERS (PDEG)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 7 group parameters ( GTN1, GTN2, GTN3, GTN4, GTN5, RTNG, SDNG, SDDG, TZSG, TZEG ):
;PDEG;

10.16 RECEIVE INTERCOM BUTTON 8 PARAMATERS (PDEH)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with all currently programmed button 8 group parameters ( HTN1, HTN2, HTN3, HTN4, HTN5, RTNH, SDNH, SDDH, TZSH, TZEH ):
;PDEH;

10.17 STATE OF THE CREDIT FOR THE PREPAID CARD

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with Credit amount on your prepaid SIM card (Vodafone UK & 02 UK and Ireland):
;
PCC1;

10.18 STATE OF THE OUTPUTS (PORC)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with current outputs state.
;PORC;

page38image16968 page38image17128 page38image17288 page38image17448 page38image17608 page38image17768 page38image17928 page38image18088 page38image18248 page38image18408

Page 38

QF BESPOKE SET UP MANUAL 10.19 MANUAL GSM MODULE RETARD (MRES)

By sending this command to QF BLACK GSM CONTROLLER shuts down GSM module and after a few second it switches the power of the GSM module ON again. The unit reboots all parameters from the SIM card. ;MRES;

10.20 RECEIVE STATUS OF INPUTS (INS)

By sending this command to QF BLACK GSM CONTROLLER you receive SMS message with current input state.

;INS;
10.21 RECEIVE QF BLACK GSM CONTROLLER LOG

By sending this command to QF BLACK GSM CONTROLLER you receive SMS messages with log events as per the LOGN parameter from the QF BLACK GSM CONTROLLER device.

;PLOG;

page39image7448 page39image7608 page39image7768 page39image7928 page39image8088 page39image8248

Page 39

QF BESPOKE SET UP MANUAL

page40image1376

11 CHANGING PARAMETERS USING THE SMS COMMAND

All programming parameters for QF BLACK GSM CONTROLLER can also be sent by SMS command. Each SMS command should start and stop with semicolon. If a confirmation SMS is needed, put "+" at the beginning of the command SMS.

The first SMS is SMS with telephone numbers (TN1 - TN4). If you would like to check which authorised user telephone numbers are programmed in QF BLACK GSM CONTROLLER please use the following command: ;PTN;

Return SMS is (example):

;TN1=;TN2=;

If you would like to enter telephone numbers in to QF BLACK GSM CONTROLLER you can use the following example:
;TN1=07796176354;TN2=+447796176355;

If you would like to receive confirmation SMS write "+" before SMS command: ;+TN1=07796176354;TN2=+447796176354;

Return SMS from QF BLACK GSM CONTROLLER is:

;TN1=07796176354;TN2=+447796176354;

It is also possible to change different parameters with one SMS. Consider that the SMS message should not be longer than 160 characters (included space characters).

If you would like to change the following parameters TN1, IN1, IN2, OS1, OS2; ID1, LN1 and CRE and would like to receive confirmation SMS, try next example: ;+TN1=+447796176354;IN1=1;IN2=1;OS1=15;OS2=1;ID1=120;LN1=1;

Send SMS message to QF BLACK GSM CONTROLLER telephone number and in a few seconds you receive SMS message from QF BLACK GSM CONTROLLER. The sentence of the SMS must be the same as the one you have sent to QF BLACK GSM CONTROLLER before.

page40image14768

NOTE

page40image16840 page40image17000

You can use the same programming procedure for all parameters.

page40image18392 page40image18552

Page 40

QF BESPOKE SET UP MANUAL

page41image1384

12 DEFAULT SETTINGS ON CONTROLLER

page41image2152
page41image3240

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

Name Default Value Short Description

TN1 Empty Telephone number 1

TN2 Empty Telephone number 1

TN3 Empty Telephone number 2

TN4 Empty Telephone number 3

TN5 Empty Telephone number 4

IN1 0 Input 1 control

IN2 0 Input 2 control

OS1 5 Output 1 mode

OS2 5 Output 2 mode

OD1 1 Input 1 direct output link

OD2 0 Input 2 direct output link

OD5 0 NAC direct output link

LN1 Empty Input 1, link to tel. numbers

LN2 1 Input 2, link to tel. numbers

LN5 Empty Periodic SMS text, link to tel. numbers

LN6 Empty SIM card refill, link to tel. numbers

LN7 Empty NAC, link to tel. numbers

LN8 Empty LOG full, link to tel. numbers

ID1 1 Input 1 delay filter on input

ID2 120 Input 2 delay filter on input

DD1 0 Input 1 delay before dialing

DD2 0 Input 2 delay before dialing

SL 0 Security level

#0 "User Location" SMS main head text

#1 "Input1" SMS input 1 text

#2 "Input2" SMS input 2 text

CC1 Empty Check credit Num 1

ESC 0 Input used as cancel button

UDC Empty

Tel. number of QF BLACK GSM CONTROLLER device

HTN 1 Hidden telephone number

RAN 0 Auto answer ring number

SCV 0 SIM card time validity

TST 24 Periodic test SMS timeout

MIC 15 Microphone volume ( 0 - 40 ) recommend 4

MUT 0 Mute functionality

SPK 10 Speaker volume ( 0 - 20 ) recommend 12

LCV 4 Low credit value

LOT 90 Connection time out value

LOGN 5 Number of log events for printing out

page41image86496 page41image99856 page41image113216 page41image113376

Page 41

QF BESPOKE

SET UP MANUAL

page42image2264

LOGI 0 Log interface

ALC 1 Automatic log clear

ADF 90 Auto dial functionality ( Call TN1 )

ARST 0 Automatic reset timeout

CREF "EUR" Parse text( contact support )

OP1 1 Output invert 1

OP2 1 Output invert 2

BUZ 1 Buzzer control

SPO 1 SIM card starting position

CLPEN 1 Enable CLIP functionality

CLPOU 1 Control output pin when CLIP event

CLPI 0 CLIP input activation condition

CLP1 Empty CLIP number 1

..

..

..

CLP100 Empty CLIP number 100

A TN1

Empty

Button 1, Telephone number 1

A TN2

Empty

Button 1, Telephone number 2

A TN3

Empty

Button 1, Telephone number 3

A TN4

Empty

Button 1, Telephone number 4

A TN5

Empty

Button 1, Telephone number 5

RTNA

25

Ring time, Button 1

SDNA

0 DTMF number to send

page42image58704

SDDA

0 Delay for DTMF to send

page42image61576

TZSA

0 Time zone start interval

page42image64400

TZEA

0 Time zone end interval

page42image67408

BTN1

Empty

Button 2, Telephone number 1

BTN2

Empty

Button 2, Telephone number 2

BTN3

Empty

Button 2, Telephone number 3

BTN4

Empty

Button 2, Telephone number 4

BTN5

Empty

Button 2, Telephone number 5

RTNB

25

Ring time, Button 2

SDNB

0 DTMF number to send

page42image90168

SDDB

0 Delay for DTMF to send

page42image93040

TZSB

0 Time zone start interval

page42image95864

TZEB

0 Time zone end interval

page42image98872

CTN1

Empty

Button 3, Telephone number 1

CTN2

Empty

Button 3, Telephone number 2

CTN3

Empty

Button 3, Telephone number 3

CTN4

Empty

Button 3, Telephone number 4

CTN5

Empty

Switch 3, Telephone number 5

RTNC

25

Ring time, Button 3

SDNC

0 DTMF number to send

page42image121632

SDDC

0 Delay for DTMF to send

page42image124496

TZSC

0 Time zone start interval

page42image127336
page42image128256 page42image143800 page42image171024 page42image171184

Page 42

QF BESPOKE

SET UP MANUAL

page43image1896

TZEC

0 Time zone end interval

page43image5136

DTN1

Empty

Button 4, Telephone number 1

DTN2

Empty

Button 4, Telephone number 2

DTN3

Empty

Button 4, Telephone number 3

DTN4

Empty

Button 4, Telephone number 4

DTN5

Empty

Button 4, Telephone number 5

RTND

25

Ring time, Button 4

SDND

0 DTMF number to send

page43image27896

SDDD

0 Delay for DTMF to send

page43image30768

TZSD

0 Time zone start interval

page43image33592

TZED

0 Time zone end interval

page43image36600

ETN1 Empty Button 5, Telephone number 1

ETN2 Empty Button 5, Telephone number 2

ETN3 Empty Button , Telephone number 3

ETN4 Empty Button 5, Telephone number 4

ETN5 Empty Button 5, Telephone number 5

RTNE 25 Ring time, Button 5

SDNE 0 DTMF number to send

SDDE 0 Delay for DTMF to send

TZSE 0 Time zone start interval

TZEE 0 Time zone end interval

FTN1 Empty Button 6, Telephone number 1

FTN2 Empty Button 6, Telephone number 2

FTN3 Empty Button 6, Telephone number 3

FTN4 Empty Button 6, Telephone number 4

FTN5 Empty Button 6, Telephone number 5

RTNF 25 Ring time, Button 6

SDNF 0 DTMF number to send

SDDF 0 Delay for DTMF to send

TZSF 0 Time zone start interval

TZEF 0 Time zone end interval

GTN1 Empty Button 7, Telephone number 1

GTN2 Empty Button 7, Telephone number 2

GTN3 Empty Button 7, Telephone number 3

GTN4 Empty Button 7, Telephone number 4

GTN5 Empty Switch 7, Telephone number 5

RTNG 25 Ring time, Button 7

SDNG 0 DTMF number to send

SDDG 0 Delay for DTMF to send

TZSG 0 Time zone start interval

TZEG 0 Time zone end interval

HTN1 Empty Button 8, Telephone number 1

HTN2 Empty Button 8, Telephone number 2

HTN3 Empty Button 8, Telephone number 3

HTN4 Empty Button 8, Telephone number 4

HTN5 Empty Button 8, Telephone number 5

page43image106784 page43image122328 page43image141872 page43image142032

Page 43

QF BESPOKE

SET UP MANUAL

page44image1672

RTNH

25

Ring time, Button 8

SDNH

0

DTMF number to send

SDDH

0

Delay for DTMF to send

TZSH

0

Time zone start interval

TZEH

0

page44image20048

Time zone end interval

Table 24: QF BLACK GSM CONTROLLER default settings

page44image21928 page44image22088

Page 44

QF BESPOKE SET UP MANUAL

page45image1432

13 PARAMTERES PRINT-OUT COMMANDS

page45image2160
page45image3264

QF BLACK GSM CONTROLLER PROGRAMMING TABLE

Name Short Description

PALL

Prints all parameters available on QF BLACK GSM CONTROLLER.

PSW Prints SW version of QF BLACK GSM CONTROLLER.

PSQ

Prints GSM network signal quality of QF BLACK GSM CONTROLLER.

PTN Prints TNx numbers.

PLN Prints LNx links.

PIN Prints INx parameters.

PID Prints IDx parameters.

POD Prints ODx parameters.

PDD Prints DDx parameters

PSL Prints SL parameter.

POS Prints OSx parameters.

P# Prints #x parameters.

PPA Prints various setup parameters.

PCLP Prints CLIP parameters.

PLOG Prints log of the QF BLACK GSM CONTROLLER.

PCREF Prints credit pars parameters.

PCN Prints credit request numbers.

PCC1

Prints credit for QF BLACK GSM CONTROLLER (universal request).

INS Prints status of the inputs.

PORC Prints (controls) the status of outputs.

PDEA

Prints intercom button 1 parameters.

PDEB

Prints intercom button 2 parameters.

PDEC

Prints intercom button 3 parameters.

PDED

Prints intercom button 4 parameters.

PDEE Prints intercom button 5 parameters.

PDEF Prints intercom button 6 parameters.

PDEG Prints intercom button 7 parameters.

PDEH Prints intercom button 8 parameters.

page45image63360

PERR Special debug command, contact supplier for details.

page45image64672

Table 25: QF BLACK GSM CONTROLLER parameters print out commands

page45image76440 page45image76600

Page 45

QF BESPOKE SET UP MANUAL

page46image1368

14 TECHNICAL SPECIFICATION

page46image2056

Description

page46image4184

Value

Power Supply

12 - 24V AC/DC

page46image8000

Current consumption - peak

1A

page46image10088

Current consumption - transmitting mode

250mA

page46image12560 page46image13360

Current consumption - idle mode

75mA

Tri band GSM module

900/1800 MHz

page46image17112

PCB dimensions

106 × 89 mm

page46image19240

Unit dimensions

118 × 170 × 60 mm

page46image21608

Call buttons

Up to 8

page46image24016

Antenna SMA

1

page46image26024

Weight

122 gr.

page46image28376 page46image29176

Alarm inputs

2

outputs (relay)

2

page46image32952 page46image33536
page46image33960 page46image34120

Page 46 

page1image33624 page1image33792 page1image33960

By SMS:

Output 1 ON

;+ORC1=1;

Output 2 ON

;+ORC2=1;

Output 1 OFF (only if set to latching)

;+ORC1=0;

Output 2 OFF (only if set to latching)

;+ORC2=0;

By Caller ID (dial in): Call the SIM card in the device from one of the numbers programmed in as a Caller ID User (CLP1 - CLP100). Send ;+CLPEN=2; and the device can then be operated by any number. Send ;+CLPEN=1; to set it back to authorized Users only.

Press to Exit: You can connect a pushbutton to alarm input 1 & ground and switch output 1 by pressing it. Send ;+OD1=1; and then connect the button (activate input 1).

TROUBLESHOOTING

Please check the following before calling for support.

  1. Will not connect: Change network, move antenna or check it is connected properly, try before installing (Blue LED should flash 3 - 5 times - 1 or 2 flashes is low signal)

  2. Audio interference on the phone: Move antenna to new location, improve signal, don't put antenna near speaker

  3. Will not call: Set User number/s to call (ETN1-ETN5) or check SIM card is working in a phone first

  4. Gate release doesn't work: Check connections on gate control side are to 'open' or 'start'

TECHNICAL SUPPORT 

G2 GSM CONTROLLER V2.0 COMPLETE MANUAL

200 User Caller ID Access Control - Event Log (1015)  - GSM Audio Intercom System

Introduction...

  1. The G2 GSM controller enables control of virtually any device via authorised telephones & management from Authorised Administrator mobile phones

  1. G2 has an inbuilt event log which stores input & output activity and is accessible by SMS or PC

  1. 2 configurable alrm inputs allow SMS text alerts to be easily sent to selected Authorised mobile phones

  1. 2 configurable outputs enable various combinations of switching to enable any device to be switched from gates, barriers, magnetic locks. lights, heating etc.

  1. G2 GSM intercom function enables 2 way wireless intercom communication from the GSM call point to land-line or mobile phones of the User's choice

Click the following Heading links to view that section of the guide

  1. QUICK START GUIDE (start here for the most basic set up)
  2. a) Make the Minimum Connections
  3. b) Insert any Activated SIM card
  4. c) Power Up & wait for the Blue LED to start flashing
  5. d) Set a User Phone Number to Test...
  6. e) Call G2 to test the output...
  7. GUIDE TO SMS TEXT MESSAGE PROGRAMMING
  8. a) Benefits of G2 SMS Text Based Programming
  9. b) SMS Text Based Programming Explained (please read carefully)
  10. G2 TECHNICAL OVERVIEW
  11. a) Hardware Description & Connection Diagram
  12. b) Hardware Features
  13. c) Technical Specifications & Values
  14. GUIDE TO PC PROGRAMMING VIA USB
  15. a) PC Programming using any Windows PC
  16. CALLER ID DEVICE CONTROL [CLIP] mobile phone dialing in to switch G2
  17. a) Disable the CLIP Feature (CLPEN=0)
  18. b) * Enable CLIP  'Authorised Callers Only - 200 Users' (CLPEN=1) (default setting)
  19. c) Enable CLIP  'Any Caller Mode' - Unlimited Users (CLPEN=2)
  20. d) Choose which Output to Switch (CLPOU=1)
  21. e) Link the CLIP feature to an actived Input in order to enable (CLPI=0)
  22. f) Retrieve the 200 User List in Full or in Parts to Delete or Add New Users (PCLP=xy,xx)
  23. g) Add or delete Authorised Callers (CLP1 - CLP200)
  24. SET UP TO 5 AUTHORISED ADMINISTRATORS FOR PROGRAMMING & ALERTS
  25. a) Add or delete Authorised Administrator Mobile Numbers (TN1 - TN5)
  26. b) Set up Active Authorised Administrator Mobile Numbers (SL)
  27. c) Link Events from Inputs or Preset Events to Authorised Administrators (LN1 - LN6)
  28. CALLER ID EVENT LOG
  29. a) Set up the Self Updating Clock (UDC)
  30. b) Change the Event Log Buffer from Auto Clear to Manual Clear & Send Alert at 900 events (ALC)
  31. c) Request Event Log by SMS Text Message (PLOG)
  32. d) Set the default amount of Events to receive by SMS Text Message (LOGN)
  33. e) Request how many Events are in the Current Event Log (PLOG=?)
  34. f) Request Event Logs between a set range of Total Events (PLOG=xy,xx)
  35. g) How to find the most Recent Events
  36. h) After Retrieving & Saving the Event Log to your PC, Erase completely by SMS Text (LCLR)
  37. OUTPUTS FOR SWITCHING DEVICES
  38. a) Request Current Output Switch Status Pulse, Latch, Timed, 1st call ON / 2nd OFF (POS)
  39. b) Request Current Output State  (PORC)
  40. c) Change Output Switching Status Pulse, Latch, Timed, 1st call ON / 2nd call OFF (OS1 & OS2)
  41. d) Change an Output Contact between Open [going closed] or Closed [going open] (OP1 & OP2)
  42. e) Make an Output Directly Switch when an Input 1 is Activated (OD1) ie: press to exit input
  43. f) Make an Output Directly Switch when an Input 2 is Activated (OD2) ie: siren/flashing beacon
  44. g) Make an Output Directly Switch when a GSM Network Error occurs (OD3)
  45. h) Make an Output Directly Switch when an Unauthorised Caller calls G2 (OD4)
  46. i) Control an Output by SMS Text Message (ORC)
  47. SET UP INPUTS FOR SMS TEXT ALERTS or GSM INTERCOM CALL BUTTONS
  48. a) Change how inputs trigger & whether an SMS text is sent to notify 'input restored' (IN1 & IN2)
  49. b) Change the time delay before SMS text alerts are sent after inputs activated (ID1 & ID2)
  50. c) Request the current Device labels for the SMS Text Alerts (P#)